A project of Sense Future
Strategic plan and field guide

Civilised Blackout

How a community keeps every person safe, warm, watered, connected and organised through a long loss of power, phones and internet.

Written so that anyone can follow it, by torchlight if needed. Built on the Sovereignty model: citizens forming their own local government, in which everyone has a role.

Version 1.0, 14 November 2026. Written for communities everywhere. Print this guide now. Keep one copy at home and one in the street's shared box.

How to use this guide

This guide is for communities everywhere, and it has two jobs. It is a strategic plan: what we prepare now, what we do in the first hours, and how we organise ourselves if the outage lasts weeks. And it is a field guide: step-by-step instructions for making water safe, building a pedal generator, setting up dry toilets, running the street's own network and email, and more.

How it is organised

Where to start

Every instruction has been checked against official or expert sources, cited in the footnotes. Where experts disagree, or where something is uncertain, the guide says so. Where a step can injure or kill if done wrongly, it is marked with a warning box like this:

Warning. Never run a petrol engine, generator, barbecue or camping heater indoors, in a garage, or near an open window. Carbon monoxide has no smell and kills in minutes.

Contents

Part Two: the chapters

  1. Chapter 12. Self-governance: Sovereignty model in full
    1. 12.1 Sovereignty model in brief
    2. 12.2 Leadership roles and their working groups
    3. 12.3 Street Charter
    4. 12.4 Choosing role holders
    5. 12.5 Making street rules: weighted vote
    6. 12.6 Running your first meeting
    7. 12.7 Daily rhythm
    8. 12.8 Sharing fairly: rules for shared stores
    9. 12.9 Growing outward: street, neighbourhood, area
    10. 12.10 Welcome is our defence: outsiders and roaming groups
    11. 12.11 Disputes
    12. 12.12 Street records
  2. Chapter 13. Water and sanitation in detail
    1. 13.1 How much water
    2. 13.2 Where water is hiding in your home
    3. 13.3 Other sources around you
    4. 13.4 Making water safe: decision chart
    5. 13.5 Methods, step by step
    6. 13.6 Clearing cloudy water, and distilling
    7. 13.7 Bought filters: best value
    8. 13.8 Street water station
    9. 13.9 Storing water
    10. 13.10 Toilets without water
    11. 13.11 Handwashing: tippy tap
    12. 13.12 Diarrhoea and dehydration
    13. 13.13 Rubbish, toilet waste and pests
  3. Chapter 14. Electricity in detail, and pedal generator
    1. 14.1 Power and energy figures
    2. 14.2 Power you already have
    3. 14.3 Cars as generators
    4. 14.4 Solar power
    5. 14.5 Build your pedal generator
    6. 14.6 Bicycle dynamos
    7. 14.7 Street power station
    8. 14.8 Petrol generators and house wiring
    9. 14.9 Lithium battery fire safety
  4. Chapter 15. Communications in detail
    1. 15.1 What works and what does not
    2. 15.2 Layered plan
    3. 15.3 Layers 1 to 3: basics
    4. 15.4 Layer 4: phone to phone with BitChat
    5. 15.5 Layer 5: street network (our local internet)
    6. 15.6 Layers 6 and 7: between streets and neighbourhoods
    7. 15.7 Layer 8: outside world and Starlink
    8. 15.8 Why not build our own Bluetooth app?
    9. 15.9 Rumours and information
  5. Chapter 16. Street network and community hub
    1. 16.1 Requirements and constraints
    2. 16.2 Bluetooth and iPhone question
    3. 16.3 Architecture
    4. 16.4 Hardware and power
    5. 16.5 Network design
    6. 16.6 Addresses and HTTPS
    7. 16.7 What to prepare now, while internet access works
    8. 16.8 Community app on your hub
    9. 16.9 Running it day to day
    10. 16.10 Security and privacy
    11. 16.11 Failure modes and recovery
    12. 16.12 Rehearsal before relying on it
    13. 16.13 Timeline and costs
  6. Chapter 17. Community email and relay
    1. 17.1 Why email, and why it works without internet access
    2. 17.2 Can email run over Bluetooth?
    3. 17.3 Design
    4. 17.4 Set up your hub mail server (prepare now)
    5. 17.5 Connect phones and computers (nothing to install)
    6. 17.6 Anchor relay
    7. 17.7 Security and privacy
    8. 17.8 Power and capacity
    9. 17.9 Rehearsal tests
    10. 17.10 Should your street build its own app?
    11. 17.11 Community app mail and hub mail
  7. Chapter 18. Warmth, shelter and safety in detail
    1. 18.1 Staying warm at home
    2. 18.2 Street warm room
    3. 18.3 Hypothermia
    4. 18.4 Carbon monoxide
    5. 18.5 Fires, gas and fireplaces
    6. 18.6 Heat and hot climates
    7. 18.7 Keeping homes safe
    8. 18.8 Flats and tall buildings
    9. 18.9 Pipes in empty or unheated homes
    10. 18.10 If you must leave home: rest centres
    11. 18.11 Fires with no fire brigade
  8. Chapter 19. Food in detail
    1. 19.1 Eating order
    2. 19.2 Cooking without electricity
    3. 19.3 Babies, special diets and pets
    4. 19.4 Shared kitchen (longer outages)
    5. 19.5 Street food stocktake and rations
  9. Chapter 20. Health and care in detail
    1. 20.1 Medicines
    2. 20.2 People on powered medical equipment
    3. 20.3 First aid essentials
    4. 20.4 Preventing illness
    5. 20.5 Mental health
    6. 20.6 Skills
    7. 20.7 When someone dies
  10. Chapter 21. Local AI, LoRA and offline library
    1. 21.1 Models that matter (November 2026)
    2. 21.2 What you need to run them
    3. 21.3 Software
    4. 21.4 What to download now
    5. 21.5 LoRA explained
    6. 21.6 Training your own adapter
    7. 21.7 Serving AI to your street
    8. 21.8 Checklist
Part One

Guide

Everything a community needs to know, in order. Each part gives the essentials and links to the chapter in Part Two that holds the full detail, instructions and frameworks.

Part 1Strategy

1.1 Why this plan exists

Governments in many countries now tell households to prepare to look after themselves for days. For example, the UK Government's Be Ready campaign asks every household to be ready for three days without outside help, with water, food, a torch, a radio, a power bank, cash and medicines.1 The European Union asks for at least 72 hours of self-sufficiency,2 and national advice is similar or longer: Finland and the Netherlands at least three days,34 Sweden at least a week5 and Germany ten days.6

Recent events show why:

Grid operators plan for a total shutdown. In Great Britain, for example, the national grid operator must be able to restore 60% of electricity demand in every region within 24 hours of a total national blackout, and 100% within five days, from the end of 2026.12 That standard covers a technical failure. It does not cover deliberate attacks on many sites, damage to large transformers that take months to replace, a fuel crisis or war. This plan therefore prepares for three scenarios:

ScenarioLengthWhat it needs from us
A: Short outageUp to 3 daysEach household copes with its own kit. Neighbours check on each other.
B: Long outage3 days to 2 weeksThe street organises: shared water, shared power, a warm room, a local network, care for vulnerable people.
C: BreakdownWeeks or longerThe street governs itself under an agreed model, grows into the wider neighbourhood, and keeps law, order and decency until normal services return.

1.2 What fails, and when

Systems do not all fail at once. Knowing the order lets us act before each one goes.

WhenWhat happensWhat we do
Minute 0Lights, sockets, electric heating, electric cookers, fridges, Wi-Fi routers, lifts, traffic lights, most shop tills. Gas central heating stops too, because boilers need electricity.13Torches on. Check on people. Start the First Hour card.
Minutes to hoursDigital landline phones stop unless they have a battery backup.14 Mobile masts run on batteries that last from minutes to a few hours; in the UK, for example, the regulator Ofcom's resilience guidance, updated in June 2026, sets no fixed number of hours.15 Mobile data and calls fail.Send key messages early. Then switch phones to aeroplane mode to save battery.
HoursCard machines and cash machines without backup power stop (many tills stop at once). Petrol pumps stop. Trains, trams and metro services stop. Fridges warm up (food safe for about 4 hours if the door stays shut).16Use cash. Keep fridge and freezer doors shut.
Hours to daysMains water may keep flowing for a while, because some supply is by gravity and some pumping stations have generators. Pressure can then drop. Sewage pumping stations may stop, and sewers can back up.Fill the bath, pans and bottles at once. Prepare a dry toilet.
Day 1 to 2Full freezers stay frozen for about 48 hours if kept shut (24 hours if half full).17 Homes get cold quickly in winter. Phone batteries run out.Cook from the freezer first. One warm room. Power rota.
Day 3 onwardsHousehold supplies run short. Shops are empty or shut. Medicines run low. Stress rises. Rumours spread.The street organises (Chapter 12). Shared stores, shared water, shared power, notice board.
Week 2 onwardsHealth risks rise from poor water and sanitation. Cold and isolation threaten older people. Some groups may roam looking for supplies.Self-governance, water treatment for all, sanitation, welcome and safety team.

1.3 Strategy on one page

Our aim

No one on our street dies, falls seriously ill or is left alone because the power went out. We keep each other safe, warm, fed, watered, informed and organised until normal services return, and we help the streets around us do the same.

Five principles

  1. The street is the unit. Help comes from the people within a few doors of you long before it comes from anywhere else. We organise at the level of our own street first, then grow outward.
  2. Everyone has a role, and everyone is critical. Every adult and child old enough belongs to a working group and owns a specific responsibility. Nobody is a gofer. People are voted into leadership roles and can be voted out. If a role is too hard for someone, their role changes. No one is left without one.
  3. Share and record. Shared stores (water, fuel, batteries, medicines) are written down, guarded fairly and given out by agreed rules.
  4. Nobody is a threat; welcome is our first defence. We invite outsiders, including desperate or aggressive groups, to join a working community with a role, a share and a vote. A growing, organised community is safer than a walled one.
  5. Order beats chaos. Prepare before, organise fast. Most of what saves lives is done before the blackout: knowing your neighbours, and at least one person on each neighbouring street, with an agreed meeting place and time. After it starts, the street organises within hours, not days.

Six foundations

FoundationGoalPart
People and governanceA street where neighbours know each other, with elected roles and fair rules.Part 3
Water and sanitation3 litres of safe drinking water per person per day, more for hygiene; safe toilets; clean hands.Part 4
Warmth and safetyNo one cold, no carbon monoxide, no fires.Part 7
PowerEnough electricity for lights, phones, radios, the street network and medical devices.Part 5
CommunicationEveryone can reach the street, the street can reach the neighbourhood, and the neighbourhood can reach the outside world.Part 6
Food and healthNobody hungry, medicines managed, illness treated early.Parts 8 and 9

1.4 Priorities: what kills first

A rough rule used in survival training is the "rule of threes": a person can survive about 3 minutes without air, about 3 hours exposed to severe cold or wet without shelter, about 3 days without water, and about 3 weeks without food.18 It is a guide, not science, but it gives the right order. In a winter blackout in a cold climate the real killers are, in order:

  1. Carbon monoxide and fire from people heating and cooking indoors with the wrong things.
  2. Cold, especially for older people living alone.
  3. Loss of medical support: oxygen, home dialysis, insulin, ventilators, medicines running out.
  4. Dirty water and poor sanitation, causing diarrhoea and dehydration, worst for babies and older people.
  5. Isolation and panic, which turn manageable problems into deadly ones.

In a hot climate or a heatwave the dangers are different: heat illness and dehydration, especially for older people, babies, and people with heart or lung conditions; food that spoils quickly; medicines that must stay cool; and mosquitoes breeding in stored water (section 18.6).1920

Research on disasters supports the street-first approach. Studies of the 1995 Kobe earthquake and other disasters by the political scientist Daniel Aldrich found that the strength of social ties between neighbours was the strongest predictor of how well a community recovered, stronger than money or the amount of damage.2122 Disaster sociologists have also found, over decades, that mass panic is rare: most people help each other.23 Our job is to make that help organised.

1.5 Phases

PhaseMain tasks
Now (before)Household kits. Meet every household on the street. Agree the meeting place and time. Make a link with at least one person on each neighbouring street. Find the street's assets (Starlink, electric cars, solar batteries, generators, medical skills). Install offline apps. Build or buy the pedal generator and the street network kit. Print this guide.
Hour 0 to 1First Hour card. Safety, light, water filling, check on vulnerable neighbours, first street gathering.
Day 1Street meeting. Interim roles. Census. Water and toilet plan. Power rota. Warm room if cold.
Days 2 to 3Day 3: first election, at the first community meeting. Street network running. Water station. Shared kitchen if needed. Contact with neighbouring streets.
Days 4 to 14Routine: daily briefing, weekly community meeting, rotas. Neighbourhood council meeting regularly (it first meets on day 3; street links meet from day 1). Starlink link to the outside world.
Beyond 2 weeksFull self-governance. Food production and sharing. Health and sanitation at group scale. Cooperation with any returning authorities.

First Hour card: what to do when power fails

  1. Light, not flame. Torches and battery lanterns. Avoid candles; if you must use one, never leave it, keep it in a jar or on a plate, away from curtains.
  2. Check your home. Is it just your house? Look at the street. Check your fuse box: if your trip switch has gone, it may be only you. If the whole street is dark, it is a wider cut.
  3. Report and listen. Report the power cut once to your electricity network's number if lines work (Appendix B; in Great Britain, 105).24 Switch on a battery or wind-up radio and find your national or local public radio station on FM (in the UK: BBC Radio 4, or your BBC local station).
  4. Fill water now. While taps still run: fill bottles, pans and the kettle for drinking from the kitchen cold tap (flats: ask, section 18.8), and fill the bath and buckets for washing and flushing. Cover them, and keep small children away from baths and buckets of water.
  5. Protect the cold. Do not open the fridge or freezer unless you must.
  6. If it is hot: keep curtains closed on the sunny side, move people at risk to the coolest room, and drink regularly (section 18.6).
  7. Switch off. Turn off appliances that could start a fire or a surge when power returns (heaters, cookers, irons). Leave one light switched on so you know when power is back.
  8. Save phone battery. Send one short message to family if you can, then put the phone in aeroplane mode. Turn on Wi-Fi only when you need the street network.
  9. Check on neighbours. Knock on the doors of anyone old, ill, disabled, alone, or with a baby. Use the vulnerable neighbours list if the street has one.
  10. Gather. When the power has been off for one hour, go to the agreed street meeting place at the next full hour, or at 08:00 if that falls at 21:00 or later, or earlier than 07:00 (section 2.4). Bring this guide. Street links go to the neighbourhood meeting place at the agreed time.
  11. Stay safe. No engines, barbecues, camping stoves or gas heaters indoors. Ever.

Notes

  1. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  2. European Commission, "Preparedness" (Preparedness Union Strategy, March 2025: at least 72 hours of self-sufficiency). https://commission.europa.eu/topics/preparedness_en (accessed 14 November 2026). Back to text
  3. Finnish National Rescue Association, "72 hours" (households should cope independently for at least three days). https://72tuntia.fi/en/ (accessed 14 November 2026). Back to text
  4. Government of the Netherlands, "Denk vooruit" (be ready for the first 72 hours of an emergency). https://www.denkvooruit.nl/ (accessed 14 November 2026). Back to text
  5. Swedish Civil Defence Agency, "Advice for individuals" (home preparedness for at least a week). https://www.mcf.se/en/advice-for-individuals/ (accessed 14 November 2026). Back to text
  6. Federal Office of Civil Protection and Disaster Assistance (BBK), Germany, "Vorsorge" (food and drink for ten days). https://www.bbk.bund.de/DE/Warnung-Vorsorge/Vorsorge/vorsorge_node.html (accessed 14 November 2026). Back to text
  7. ENTSO-E Expert Panel, "28 April 2025 Iberian Blackout: Final Report", ENTSO-E, March 2026. https://www.entsoe.eu/publications/blackout/28-april-2025-Iberian-blackout (accessed 14 November 2026). Back to text
  8. Reuters, "Power restored in Berlin after five days", reported in Dawn, January 2026. https://www.dawn.com/news/1965710/power-restored-in-berlin-after-five-days (accessed 14 November 2026). Back to text
  9. Clean Energy Wire, "Berlin blackout" coverage, January 2026. https://www.cleanenergywire.org/node/15499 (accessed 14 November 2026). Back to text
  10. Stromnetz Berlin, press release on the end of the power outage in Treptow-Koepenick, September 2025. https://www.stromnetz.berlin/en/about-us/press/press-releases-2025/5-updateend-of-power-outage-storung-treptow-kopenick/ (accessed 14 November 2026). Back to text
  11. Hromadske, "Invincibility points in Kyiv: what has been achieved and what needs to be worked out", 2022. https://hromadske.ua/en/posts/invincibility-points-in-kyiv-what-has-been-achieved-and-what-needs-to-be-worked-out-photo-report (accessed 14 November 2026). Back to text
  12. National Energy System Operator (NESO), "Electricity System Restoration Standard". https://www.neso.energy/industry-information/balancing-services/electricity-system-restoration-standard (accessed 14 November 2026). Back to text
  13. Which?, "What to do in a power cut" (gas boilers need electricity; gas hobs can be lit with a match). https://www.which.co.uk/reviews/energy-companies/article/power-cuts/what-to-do-in-a-power-cut-aVPIj7v1DXsA (accessed 14 November 2026). Back to text
  14. Ofcom, "Stay connected in severe weather" (landlines and power cuts). https://www.ofcom.org.uk/phones-and-broadband/vulnerable-customers/stay-connected-in-severe-weather (accessed 14 November 2026). Back to text
  15. Osborne Clarke, "Regulatory Outlook July 2026: Telecoms" (Ofcom's updated resilience guidance sets no fixed hours of battery backup for mobile sites). https://www.osborneclarke.com/insights/regulatory-outlook-july-2026-telecoms (accessed 14 November 2026). Back to text
  16. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  17. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  18. Wikipedia, "Rule of threes (survival)" (a rule of thumb used in survival training). https://en.wikipedia.org/wiki/Rule_of_threes_(survival) (accessed 14 November 2026). Back to text
  19. US Centers for Disease Control and Prevention, "About Heat and Your Health" (signs of heat illness; people at higher risk; use fans only below 90°F; many medicines cause dehydration or overheating; plan for medicines that need cool storage). https://www.cdc.gov/heat-health/about/index.html (accessed 16 November 2026). Back to text
  20. World Health Organization, "Dengue" fact sheet, 21 August 2025 (cover, empty and clean domestic water storage containers every week). https://www.who.int/news-room/fact-sheets/detail/dengue-and-severe-dengue (accessed 16 November 2026). Back to text
  21. D. P. Aldrich, "The power of people: social capital's role in recovery from the 1995 Kobe earthquake", Natural Hazards 56(3), 595 to 611, 2011. https://econpapers.repec.org/RePEc:spr:nathaz:v:56:y:2011:i:3:p:595-611 (accessed 14 November 2026). Back to text
  22. D. P. Aldrich, Building Resilience: Social Capital in Post-Disaster Recovery, University of Chicago Press, 2012. Back to text
  23. E. L. Quarantelli, "Sociology of panic", in N. Smelser and P. Baltes (eds), International Encyclopedia of the Social and Behavioral Sciences, Pergamon, 2001. Back to text
  24. Energy Networks Association, "105 service" (free power cut number for England, Scotland and Wales). https://energynetworks.org/work/105-service (accessed 14 November 2026). Back to text

Part 2Prepare now

Most of this costs little. Do it in order: the first list matters most.

2.1 Every household: 3-day kit (government list, with our additions)

  • Water: 3 litres per person per day for drinking, for at least 3 days, plus extra for cooking, washing, babies and pets. For a family of four, that is at least 36 litres to drink.25
  • Food for at least 3 days that needs no fridge and no cooking: tins, dried fruit, nuts, crackers, peanut butter, cereal bars. Food you already eat.
  • Tin opener (manual).
  • Torch or head torch for each person, with spare batteries. Torches are safer than candles.
  • Battery or wind-up FM radio. Write the station frequencies on it.
  • Fully charged power bank (10,000 mAh or more) for each adult.
  • First aid kit and at least 2 weeks of every regular medicine. Order repeat prescriptions early.26
  • Hygiene: hand sanitiser, wet wipes, toilet paper, sanitary products, nappies.
  • Warmth: blankets, sleeping bags, hats, gloves, thermal layers.
  • Cash in coins and small notes.
  • Printed copies of ID, prescriptions, and a written list of contacts and medicine doses.
  • Babies: ready-to-feed formula (no boiling needed), nappies, wipes.27
  • Pets: food and water.
  • Our additions: a battery-powered carbon monoxide alarm; a whistle per person; strong bin bags and a bucket with a lid (dry toilet); water purification tablets (bleach only if its label states the exact strength: section 13.5); a lighter or matches (to light a gas hob); a printed copy of this guide.
  • Ask your energy and water suppliers to put your household on their priority list for vulnerable customers (in Great Britain, the Priority Services Register, thepsr.co.uk) if anyone in the home is older, disabled, has a medical device, or has a child under 5.28

2.2 Buy now, if you can: best-value items

These items make the biggest difference for the money. Prices are rough UK prices in pounds sterling (GBP) for late 2026: use them to compare costs.

ItemWhyRough cost
Water purification tablets (sodium dichloroisocyanurate, for example Puritabs or Aquatabs)Exact dose, keeps about 5 years, light.29 Safer than guessing with bleach.5 to 15 GBP
Hollow-fibre water filter (for example Sawyer Squeeze)Removes bacteria and parasites; then chlorinate or boil the water, because it does not remove viruses.30 Its maker states it lasts for thousands of litres.30 to 45 GBP
Water containers (20 to 25 litre jerrycans, food grade)Store and carry water.10 to 20 GBP each
Camping stove with spare gas canistersBoil water and cook (outdoors only).20 to 40 GBP
Wind-up or solar FM radio with USB outputNews without batteries; some charge a phone slowly.20 to 40 GBP
Power banks (20,000 mAh)Each one gives about 2 to 3 phone charges (20,000 mAh at 3.7 V is 74 Wh, of which about 50 Wh reaches the phone; a phone takes about 15 to 20 Wh).20 to 40 GBP
Battery carbon monoxide alarmWarns before CO kills.15 to 25 GBP
12 V USB car charger (USB-C, 45 W or more)Charges phones and laptops from any 12 V battery or car.10 to 20 GBP
Folding solar panel (60 to 100 W, USB and 12 V outputs)Free power on bright days. Much less in winter.60 to 150 GBP
Licence-free walkie-talkiesStreet team radios. Licence-free types differ by country (in the UK, PMR446)31; in town, expect a few hundred metres to about 1 km, further in open country.20 to 40 GBP a pair
Portable power station (500 Wh or more)Runs lights, router, laptop, CPAP; recharges from solar, car or pedal generator.250 to 500 GBP

2.3 Every phone and computer: install these now

Once the internet is gone, nobody can download an app. An iPhone in particular cannot receive a new app without the internet, unless it was registered in advance with a paid developer account (section 16.2.2). So install these now, on every phone in the house, and teach your family to use them.

AppWhat it does with no internetWhere
BitChat (by permissionlesstech)Text messages between nearby phones over Bluetooth; messages hop through other phones up to 7 times. Works between iPhone and Android.3233App Store (iPhone, iPad, Mac); Google Play (com.bitchat.droid). Check the developer listed: copies exist.
Organic Maps or OsmAndFull offline maps and directions. Download the map for your country or region inside the app now.App Store, Google Play
KiwixOffline Wikipedia, medical encyclopedia and survival libraries. Download "WikiMed" (about 1.7 GB) and the post-disaster library (about 0.6 GB) inside the app.34App Store, Google Play
Briar (Android only)Secure messaging over Bluetooth and Wi-Fi. Can pass itself to another Android phone with no internet.35Google Play, F-Droid
Delta ChatEnd-to-end encrypted messages over the street email (Chapter 17).App Store, Google Play, F-Droid
Meshtastic or MeshCore (only if you have a LoRa radio)Long-range text messaging through small radio devices (Chapter 15).App Store, Google Play

Also: save important phone numbers on paper; download this guide to your phone; turn on battery-saving mode now so you know where it is.

2.4 Start now: build relationships

The foundations of a community that can govern itself are relationships, and they must exist before the crisis. Start this week. Do not wait for a perfect plan.

  1. Know your street. Knock on every door on your street over the next two weeks. Introduce yourself, explain the plan in two minutes, and learn who lives there. Leave a copy of the Street Links Card (form 15) with your house number, how to reach you and the meeting arrangements.
  2. Agree a meeting place and time. A front garden, a corner, a church hall or a car park: somewhere everyone can find in the dark. Agree the rule: if the power has been off for one hour, we meet at the meeting place at the next full hour, and then every day at 10:00 and 18:00. If that time falls at 21:00 or later, or earlier than 07:00, we meet at 08:00 instead, unless someone needs urgent help. Write it on the Street Links Card and on every copy of this guide.
  3. Reach everyone. Note who is deaf, blind, or does not read the street's main language well, and give each a door-knock buddy. Translate the First Hour card and the Street Links Card into the main languages spoken on the street.
  4. Make street links. Find at least one person on each neighbouring street who agrees to be that street's link, and be (or find) our street's link to them. Exchange house numbers and meeting places. Agree a neighbourhood meeting place and time for the links (for example, the local park gate at 12:00 on the first full day of an outage, and daily after). These links are the start of the neighbourhood council.
  5. Hold a first street meeting now, before any crisis. Explain the plan. Read the Street Charter. Ask for volunteers for interim roles, so people already know who will lead each working group if the power goes.
  6. Census. With each household's consent, fill in the Household Card (form 1): who lives there, who needs help, what skills and equipment they have. Keep cards in a sealed folder held by two trusted people.
  7. Find the street's assets. Use the Asset Door Card (form 2) to ask: Who has a Starlink dish? An electric car (especially one that can power a socket, called "vehicle-to-load")? Solar panels with a home battery? A generator? A camping stove? A water butt (rain barrel)? A swimming pool or hot tub? A turbo trainer or exercise bike? Walkie-talkies? Medical, nursing, electrical, plumbing, building or radio skills?
  8. Identify vulnerable people. Anyone who lives alone, is older, disabled, pregnant, on oxygen, dialysis or other powered medical equipment, or has a baby. Each gets two "buddies" on the street who will check on them in the first hour.
  9. Build the shared kit. The street's shared box: printed guides, forms, pens, a notice board, a whistle, the pedal generator, a 12 V battery, the street network kit, chlorine tablets, a first aid kit. Fund it by voluntary contributions recorded in the ledger (or a small grant: councils and community foundations often fund community resilience), and record who holds each item.
  10. Rehearse once. Pick an evening. Switch off the main power for two hours. Run the First Hour card. Fix what went wrong. Homes with powered medical equipment (oxygen, ventilators, dialysis, powered beds) do not switch off: switch off everything else, and test the equipment's own battery and the backup plan with the care team instead.
  11. Tell your local authority. Contact its emergency planning team (in the UK, your council, which can give you your Local Resilience Forum's community emergency plan template). Ask about any local community resilience programme, and tell them your street is organising. Official recognition makes cooperation easier in a real emergency.
Official help for community groups: look for your own government's advice for community groups. For example, the UK Government's Be Ready campaign has a page for communities and community groups, which tells groups to make a plan and to contact their council or Local Resilience Forum. Use these alongside this guide: they cover the official side, this guide covers the long blackout.3637

Notes

  1. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  2. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  3. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  4. Priority Services Register (energy and water companies), thepsr.co.uk. https://www.thepsr.co.uk/ (accessed 14 November 2026). Back to text
  5. Aquatabs, "Frequently asked questions" (five-year shelf life in strip packs). https://www.aquatabs.com/faq/ (accessed 14 November 2026). Back to text
  6. US Centers for Disease Control and Prevention, "About Water Treatment Options When Hiking, Camping, or Traveling" (filters of 1 micron or smaller against Cryptosporidium; chlorine is not effective against it). https://www.cdc.gov/drinking-water/prevention/water-treatment-hiking-camping-traveling.html (accessed 14 November 2026). Back to text
  7. Ofcom, "Licence-exempt devices" (PMR446 walkie-talkies may be used without a licence). https://www.ofcom.org.uk/spectrum/radio-equipment/licence-exempt-devices (accessed 14 November 2026). Back to text
  8. permissionlesstech, "bitchat" (source code and documentation). https://github.com/permissionlesstech/bitchat (accessed 14 November 2026). Back to text
  9. permissionlesstech, "bitchat-android" releases. https://github.com/permissionlesstech/bitchat-android/releases (accessed 14 November 2026). Back to text
  10. Kiwix, ZIM file downloads (sizes as listed, November 2026). https://download.kiwix.org/zim/ (accessed 14 November 2026). Back to text
  11. Briar Project, "Briar 1.4 released" (share the app offline), November 2021. https://briarproject.org/news/2021-briar-1.4-released/ (accessed 14 November 2026). Back to text
  12. UK Government, Be Ready campaign, "Information for communities and community groups". https://beready.campaign.gov.uk/play-your-part-in-your-community/information-for-communities-and-community-groups/ (accessed 14 November 2026). Back to text
  13. UK Government, Be Ready campaign, "Information for communities and community groups" (make a plan; contact your council or Local Resilience Forum). https://beready.campaign.gov.uk/play-your-part-in-your-community/information-for-communities-and-community-groups/ (accessed 14 November 2026). Back to text

Part 3People: community self-government

When normal services stop, the most important resource on the street is the people, and whether they can decide things together quickly and fairly. The street governs itself using the Sovereignty model (sensefuture.org/sovereignty), applied in its pure form at the scale of one street and growing outward to the neighbourhood.38 The aim is a citizen-run local government that looks after every need of every person in the community.

Four rules

  1. Everyone has a role. Every resident, from about age 8 to the oldest, belongs to a working group and owns a specific responsibility.
  2. Nobody is a gofer. Everyone is critical. Every responsibility is written down with the person who holds it, and every one matters.
  3. Nobody is a threat. Every person, including strangers and people who arrive angry or desperate, is a possible member.
  4. We overcome chaos by creating order, fast. Within hours of a long outage the street meets, fills its roles, and everyone knows what they are doing.

3.1 How your street governs itself

3.2 First 72 hours

Hour 1: every home does the First Hour card and buddies check every vulnerable person. Hours 1 to 3: the first street meeting at the agreed place and time (or 08:00 if that time falls at 21:00 or later, or earlier than 07:00), the Charter adopted, interim role holders chosen, everyone in a working group. By day 2, every working group has specific responsibilities and the water station, charging station and notice board are running. Day 3: the first election, at the first community meeting, and the first neighbourhood council (each street's Coordinator and one elected delegate; street links help).

3.3 Welcome, safety and growth

Newcomers and outside groups are met by the welcome team, offered water at once, and invited to join with a role, a fair share and a vote. Nobody fights over things: people come first. The street grows by invitation: two people help the next street hold its first meeting, and each street sends its Coordinator and an elected delegate to the neighbourhood council, where the same rules apply.

In detailChapter 12: the model in full, the twelve working groups, the Street Charter, elections, challenges and recall, the community meeting, the weighted vote with a worked example, the first meeting script, the daily rhythm, rules for shared stores, the welcome protocol for groups, disputes and records. Printable forms: Appendix C.

Notes

  1. Sense Future, "Sovereignty" (the Sovereignty model: directly elected ministers, recall, weighted voting, regular voting days). https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  2. Sense Future, "Sovereignty" (the Sovereignty model: directly elected ministers, recall, weighted voting, regular voting days). https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  3. Sense Future, "The Sovereignty Act" (Draft Sovereignty Act 2025) and "Harm Principle". https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  4. Sense Future, "The Sovereignty Act" (Draft Sovereignty Act 2025) and "Harm Principle". https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text

Part 4Water and sanitation

Water is the most urgent physical need after warmth, and dirty water is the most common cause of illness after disasters.

4.1 Essentials

4.2 For your whole street

After a few days, the Water Lead runs a street water station: collect, settle, then boil, or filter through 0.1 micron (or certified) filters and chlorinate; serve from a tap, and log every batch. Group toilets are trench latrines at least 30 metres from any water source.54 Tippy taps make handwashing easy everywhere.

In detailChapter 13: every method step by step with doses, the homemade sand filter, distilling, bought filters, the street water station, storage, toilets, handwashing and dehydration.

Notes

  1. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  2. World Health Organization, Guidelines for Drinking-water Quality, fourth edition incorporating the first and second addenda, 2022. https://www.who.int/publications/i/item/9789240045064 (accessed 14 November 2026). Back to text
  3. Sphere Association, The Sphere Handbook: Humanitarian Charter and Minimum Standards in Humanitarian Response, fourth edition, 2018 (water supply standard 2.1). https://spherestandards.org/handbook/ (accessed 14 November 2026). Back to text
  4. BES, "Loft coffin cold water storage tank 227 l (50 galls)" (a common loft tank size). https://www.bes.co.uk/loft-coffin-cold-water-storage-tank-227-l-50-galls-18675 (accessed 14 November 2026). Back to text
  5. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  6. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  7. SODIS (Helvetas), "Application of the SODIS method" (at least 6 hours in full sun; 2 days if more than half the sky is cloudy). https://www.sodis.ch/methode/anwendung/index_EN.html (accessed 14 November 2026). Back to text
  8. Drinking Water Inspectorate, "Water storage tanks and cisterns" (in many older homes only the kitchen cold tap comes straight from the mains; other taps are fed from a storage tank). https://www.dwi.gov.uk/consumers/learn-more-about-your-water/water-storage-tanks-and-cisterns/ (accessed 14 November 2026). Back to text
  9. US Centers for Disease Control and Prevention, "How to Create and Store an Emergency Water Supply" (cleaning containers; replace stored water every 6 months). https://www.cdc.gov/water-emergency/about/how-to-create-and-store-an-emergency-water-supply.html (accessed 14 November 2026). Back to text
  10. UK Government, Be Ready campaign, "Water supply interruptions or outages" (bottled water is the safest way to prepare). https://beready.campaign.gov.uk/be-informed-about-hazards/water-supply-interruptions-or-outages (accessed 14 November 2026). Back to text
  11. Wellington Region Emergency Management Office, "Emergency toilets" (the two-bucket system). https://www.wremo.nz/emergency-toilets/ (accessed 14 November 2026). Back to text
  12. World Health Organization Regional Office for the Eastern Mediterranean, guidance on home-made oral rehydration solution. https://applications.emro.who.int/docs/WHOEMCSR594E-eng.pdf (accessed 14 November 2026). Back to text
  13. Sphere Association, The Sphere Handbook: Humanitarian Charter and Minimum Standards in Humanitarian Response, fourth edition, 2018 (water supply standard 2.1). https://spherestandards.org/handbook/ (accessed 14 November 2026). Back to text

Part 5Electricity

The things that matter most in a blackout (lights, phones, radios, the street network, some medical devices) need very little power. Heating, cooking and boiling water must come from gas, wood or other fuel.

5.1 Essentials

Warning. Never run an engine, generator or barbecue indoors or in a garage. Carbon monoxide kills without warning.
In detailChapter 14: the full energy tables, the car and electric car as generators, solar, the complete pedal generator build with parts, diagrams and wiring (section 14.5), battery charging rules, and the street power station.

Notes

  1. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  2. Best Chargers, "V2L explained: which UK EVs have vehicle-to-load", 2026. https://www.bestchargers.co.uk/v2l-uk-evs-explained/ (accessed 14 November 2026). Back to text
  3. US Centers for Disease Control and Prevention, "About Carbon Monoxide Poisoning" (generators more than 20 feet, about 6 metres, from windows, doors and vents; never heat a house with a gas oven). https://www.cdc.gov/carbon-monoxide/about/index.html (accessed 14 November 2026). Back to text
  4. Best Chargers, "V2L explained: which UK EVs have vehicle-to-load", 2026. https://www.bestchargers.co.uk/v2l-uk-evs-explained/ (accessed 14 November 2026). Back to text
  5. European Commission Joint Research Centre, PVGIS (Photovoltaic Geographical Information System), monthly solar output for England. https://re.jrc.ec.europa.eu/pvg_tools/en/ (accessed 14 November 2026). Back to text
  6. Battery University, "BU-403: Charging Lead Acid". https://batteryuniversity.com/article/bu-403-charging-lead-acid (accessed 14 November 2026). Back to text
  7. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text

Part 6Communications and street network

Mobile phones, landlines and the internet fail within hours. The plan builds communication in layers, from face to face up to satellite, so that every layer backs up the one above it.

6.1 Layers

  1. Face to face: meetings, the notice board, written messages, runners.
  2. Signals: whistles, torches.
  3. Walkie-talkies: licence-free types differ by country (in the UK, PMR446).
  4. Phone to phone over Bluetooth with BitChat. Install it now. An iPhone without BitChat can get it later in only two ways: at a supervised download over a shared satellite link (section 15.4), or, with no internet, if its device ID was registered in advance with a paid developer account (section 16.2.2).6263
  5. The street network: battery-powered Wi-Fi with a small server (the hub). Any phone, tablet or laptop joins and uses it in the ordinary web browser, with nothing to install.
  6. Between streets: outdoor Wi-Fi links and LoRa radios.
  7. Between neighbourhoods: LoRa radio mesh and licensed radio amateurs.
  8. The outside world: a shared Starlink dish, satellite SOS on newer phones, and FM radio for official news.

6.2 Street network and hub

The hub serves a community app for messages, notices, rotas and project planning; the offline library; this guide; an AI assistant when there is power; and app files for Android phones. To join, scan the Wi-Fi code on the poster, stay connected when the phone says "no internet", and scan the second code to open the hub.

Coordinating beyond the street. Neighbourhoods keep in contact through street email between hubs (section 6.3), LoRa radios and runners. A shared satellite link (section 6.4) reaches the rest of the world. Keep paper copies of plans and contacts.

6.3 Email that keeps working

Each hub can run a small mail server, so every person gets a personal address that works on the street network with the phone's built-in Mail app or a web browser. Mail passes between neighbourhood hubs over the Wi-Fi links and, when a satellite link is up, to and from the rest of the world through a relay outside the affected area. Mail waits safely in queues while links are down.64

6.4 Starlink

One Starlink dish, shared through the street network, can connect the whole street to the outside world. There is no public map of dishes, but there are free ways to find them: look for the Wi-Fi network called "STARLINK" with a phone, search the free WiGLE community Wi-Fi map, or map your own area with the WiGLE app.65 Agree sharing terms with owners now.

6.5 Why we do not build our own Bluetooth app

Good Bluetooth messaging apps exist (BitChat works between iPhone and Android). Without the internet, no app can be put on an iPhone that was not prepared in advance (its ID registered with a paid developer account), so a homemade app would not reach unprepared iPhones either. Bluetooth between phones reaches only a few tens of metres at best, less through walls, and carries little data.6667 So the plan uses BitChat for phone-to-phone messages and Wi-Fi with a web hub, which works on every device with a browser, for the local internet and email.

In detailChapter 15: every layer in detail, BitChat, LoRa radios, finding and sharing Starlink, and the full answer on Bluetooth apps. Chapter 16: the technical framework for the street network and hub. Chapter 17: community email and the relay.

Notes

  1. Apple, "Create an ad hoc provisioning profile" and "Distribute to registered devices", Xcode Help. https://help.apple.com/xcode/mac/current/en.lproj/dev4335bfd3d.html (accessed 14 November 2026). Back to text
  2. The Register, "Apple, Google agree to loosen grip on UK app stores", February 2026. https://www.theregister.com/2026/02/10/apple_google_uk_app_stores/ (accessed 14 November 2026). Back to text
  3. IETF, RFC 5321 "Simple Mail Transfer Protocol", the retry strategy section (mail servers queue and retry undelivered mail). https://www.rfc-editor.org/rfc/rfc5321#section-4.5.4 (accessed 14 November 2026). Back to text
  4. WiGLE, the Wireless Geographic Logging Engine (community map of Wi-Fi networks). https://wigle.net/ (accessed 14 November 2026). Back to text
  5. Bluetooth SIG, "Understanding Bluetooth range" (range depends on the radio, the antenna and obstacles). https://www.bluetooth.com/learn-about-bluetooth/key-attributes/range/ (accessed 14 November 2026). Back to text
  6. The Register, "Jack Dorsey floats specs for decentralized messaging app that uses Bluetooth", July 2025. https://www.theregister.com/2025/07/08/jack_dorsey_debuts_bitchat/ (accessed 14 November 2026). Back to text

Part 7Warmth, shelter and safety

In a winter blackout in a cold climate, cold and carbon monoxide are the two biggest dangers. Both are preventable.

In detailChapter 18: staying warm step by step, the warm room, hypothermia, carbon monoxide, fires and fireplaces, summer heat and home safety. Pull-out card: Appendix A.

Notes

  1. UK Health Security Agency and Age UK, "Top tips for keeping warm and well this winter" (heat the rooms you use to at least 18°C; several layers). https://assets.publishing.service.gov.uk/media/64fb2e2157e8840013e127ac/winter-leaflet-v3.pdf (accessed 14 November 2026). Back to text
  2. NHS, "Hypothermia". https://www.nhs.uk/conditions/hypothermia/ (accessed 14 November 2026). Back to text
  3. NHS, "Carbon monoxide poisoning". https://www.nhs.uk/conditions/carbon-monoxide-poisoning/ (accessed 14 November 2026). Back to text
  4. NI Direct, "Carbon monoxide poisoning" (like flu but no high temperature; suspect it when others have similar symptoms). https://www.nidirect.gov.uk/conditions/carbon-monoxide-poisoning (accessed 14 November 2026). Back to text
  5. Energy Networks Association, "Smell gas?" (National Gas Emergency Service, 0800 111 999). https://www.energynetworks.org/customers/smell-gas (accessed 14 November 2026). Back to text
  6. NI Direct, "Energy, power supply and utilities" (Northern Ireland gas emergency: 0800 002 001). https://www.nidirect.gov.uk/articles/energy-power-supply-and-utilities (accessed 14 November 2026). Back to text

Part 8Food

In detailChapter 19: food safety, the rocket stove (Figure 19.1), haybox cooking, babies, special diets, pets and the shared kitchen.

Notes

  1. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  2. Aprovecho Research Center, retained heat cookers (test results: about 50% of fuel and cooking time saved). https://aprovecho.org/category/biomass-alternatives/ (accessed 14 November 2026). Back to text
  3. GIZ, "Report: Performance Test of retained heat cooker (WonderBag)", energypedia. https://energypedia.info/images/a/af/Report_Performance_Test_of_retained_heat_cooker_%28WonderBag%29_GIZ.pdf (accessed 14 November 2026). Back to text
  4. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  5. Federal Office of Civil Protection and Disaster Assistance (BBK), Germany, "Vorsorge" (food and drink for ten days). https://www.bbk.bund.de/DE/Warnung-Vorsorge/Vorsorge/vorsorge_node.html (accessed 14 November 2026). Back to text

Part 9Health and care

In detailChapter 20: medicines, every kind of powered medical equipment, first aid essentials, preventing illness, mental health and the skills register.

Notes

  1. US Food and Drug Administration, "Information Regarding Insulin Storage and Switching Between Products in an Emergency". https://www.fda.gov/drugs/emergency-preparedness-drugs/information-regarding-insulin-storage-and-switching-between-products-emergency (accessed 14 November 2026). Back to text
  2. Priority Services Register (energy and water companies), thepsr.co.uk. https://www.thepsr.co.uk/ (accessed 14 November 2026). Back to text
  3. Resuscitation Council UK, "Adult basic life support guidelines", 2025. https://www.resus.org.uk/library/2025-resuscitation-guidelines/adult-basic-life-support-guidelines (accessed 14 November 2026). Back to text
  4. Resuscitation Council UK, "First aid guidelines", 2025 (bleeding, tourniquets, burns, choking). https://www.resus.org.uk/library/2025-resuscitation-guidelines/first-aid-guidelines (accessed 14 November 2026). Back to text
  5. NHS, "Burns and scalds" (cool for 20 minutes; cling film; no creams, oils or butter). https://www.nhs.uk/conditions/burns-and-scalds/ (accessed 14 November 2026). Back to text
  6. World Health Organization, War Trauma Foundation and World Vision International, Psychological First Aid: Guide for Field Workers, 2011. https://www.who.int/publications/i/item/9789241548205 (accessed 14 November 2026). Back to text

Part 10Knowledge: local AI and offline library

Without the internet, the street loses the world's knowledge. Two things restore much of it, both prepared in advance on a large external drive.

Warning. AI can be confidently wrong. Never rely on it alone for medicine doses, medical decisions or electrical safety.
In detailChapter 21: the models, exact hardware tiers, software, what to download now with sizes, everything about LoRA, the limits of training your own adapter, and serving the AI to the street.

Notes

  1. Qwen team, Alibaba, "Qwen3.8-27B" model card, Hugging Face, 2026. https://huggingface.co/Qwen/Qwen3.8-27B (accessed 14 November 2026). Back to text
  2. Hugging Face, model search for LoRA adapters (searched 14 November 2026 for first aid, medical, survival, emergency, disaster, preparedness, off-grid, wilderness, MedGemma, Qwen3.8 and Gemma 4 adapters). https://huggingface.co/models?other=lora (accessed 14 November 2026). Back to text
  3. Machine Learning Mastery, "RAG vs Fine-Tuning for Domain Adaptation: When to Use Which". https://machinelearningmastery.com/rag-vs-fine-tuning-for-domain-adaptation-when-to-use-which/ (accessed 14 November 2026). Back to text

Part 11Money, documents and transport

Notes

  1. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  2. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  3. Health and Safety Executive, "If you store petrol at home, or at a club/association or similar premises" (up to 30 litres in suitable containers; not in living accommodation). https://www.hse.gov.uk/fireandexplosion/petrol-storage-club-association.htm (accessed 14 November 2026). Back to text
Part Two

Chapters

The full detail behind each part of the guide: step-by-step instructions, diagrams, technical frameworks and the reasons behind each decision.

Chapter 12Self-governance: Sovereignty model in full

When normal services stop, the most important resource on the street is not water or fuel. It is the people, and whether they can decide things together quickly and fairly. A street that argues, splits into factions or lets one loud person take over will waste its water, fuel and goodwill. A street with a clear, fair way of choosing leaders and making rules will cope with almost anything.

This chapter sets out that way. It applies the Sovereignty model (published by Sense Future at sensefuture.org/sovereignty) in its pure form, at the scale of one street, and then shows how it grows to the neighbourhood. The aim is a citizen-run local government that takes care of every need of every person in the community.

Four rules that everything else rests on

  1. Everyone has a role. Every resident, from the age of about 8 to the oldest, belongs to a working group and owns a specific responsibility in it.
  2. Nobody is a gofer. Everyone is critical. No one is "just a helper". The person who keeps the handwashing station full is as necessary as the person who leads the water group, because without them people fall ill. Every responsibility is written down with the person who holds it.
  3. Nobody is a threat. Every person, including strangers and people who arrive angry or desperate, is a possible member of the community. We speak and act on that basis.
  4. We overcome chaos by creating order, fast. Panic and conflict grow where nobody knows who decides what. Within hours of a long outage, the street meets, roles are filled, and every person knows what they are doing and who they report to.

12.1 Sovereignty model in brief

At national level the Sovereignty model has five core ideas:

The national model uses the offices of a parliamentary system such as the UK's; the street version works the same way under any national system. It keeps every one of these ideas, and speeds them up to suit a crisis. It adds two things the national model does not have: the Dispute Panel, and cases for roles presented at a community meeting (section 12.4).

National Sovereignty modelStreet version
ElectorateThe Street Assembly: every resident aged 16 or over
Prime Minister (defence, security, foreign affairs)Street Coordinator: safety, relations with other streets, authorities and outsiders, and coordination of the role holders
Directly Elected MinistersRole holders, one for each area of need (water, food, health, power and so on)
Chancellor of the ExchequerRecords and Resources Keeper: the shared stores and the ledger
Constituency MPs (who also mediate local disputes)Household delegates: one per household; they also try to settle disputes between neighbours first
Direct Democracy Days (three a year)Community meeting: once a week during the crisis, then monthly once things are stable. The street's votes take place here. Roles are not re-elected on a schedule: a role changes hands when someone presents a case and wins the vote, or through recall (section 12.4). Presenting a case at a meeting is the street's own addition; the national model has no equivalent
Special Adjudicator (decides whether a bill crosses departments and needs co-sponsors)Rules Adjudicator: a resident with no leadership role, elected by the Assembly at the first election (until then, an interim one chosen at the first meeting), and challenged or recalled in the same way as a role holder, who decides whether a proposed rule crosses working groups (section 12.5)
(no national equivalent)Dispute Panel: three residents drawn by lot, for disputes the household delegates cannot settle
Harm PrincipleThe same Harm Principle, written into the Street Charter

12.2 Leadership roles and their working groups

Every need a person has (water, food, warmth, health, safety, information, company, learning, a say in decisions) belongs to one working group. Each working group is led by a directly elected role holder. Each member of a working group owns one or more specific responsibilities. Together, the twelve groups below cover every need of every person in the community.

Leadership roleWorking groupSpecific responsibilities in the group (each has an owner)
1. Street CoordinatorCoordination GroupStreet links (one person in contact with each neighbouring street); liaison with police, local authority, fire, ambulance and armed forces; emergency response plan; meeting arrangements (the chair of each meeting is drawn by lot, so the Coordinator does not chair); growth (helping new streets organise); daily briefing summary.
2. Records and Resources KeeperResources GroupCensus and household cards; the Assembly list (who may vote); shared stores and their locations; the ledger; distribution and rationing by agreed rules; lost and found; the Decisions Book; the returning officers' kit (ballot papers, box).
3. Water and Sanitation LeadWater GroupWater sources and collection; the water station (settling, 0.1 micron filtering then chlorinating, or boiling); the water log and chlorine checks; distribution times; toilets (dry toilets, latrines, bags and cover material); handwashing stations; waste collection and disposal; cleaning of shared spaces.
4. Food LeadFood GroupFood stores and stock checks; the shared kitchen and cooking rota; cooking fuel; food safety and hygiene; babies' feeding and breastfeeding support; special diets (allergy, diabetes, religious); pet food; seeds and growing; foraging rules.
5. Health and Care LeadCare GroupFirst aid post and kit; medicines list and supply; buddies for every vulnerable person; people on powered medical devices; disability and mobility support; pregnancy and new babies; infection control and isolation of the sick; contact with any doctors, nurses or clinics; deaths (recording, informing authorities, care of the family).
6. Power LeadPower GroupPedal generator and pedalling rota; batteries and the battery log; the charging station and device log; solar panels; cars and electric cars used for power; fuel storage; electrical and battery safety.
7. Communications and Network LeadCommunications GroupNotice board; news desk (radio monitoring, marking news CONFIRMED or UNCONFIRMED); runners; walkie-talkies; the street network hub and Wi-Fi; the information and registration desk; Starlink and links to the outside world; message pads.
8. Warmth and Shelter LeadShelter GroupThe warm room and its rota; heating safety and carbon monoxide alarms; fire safety and fire watch; housing for people whose homes are unsafe or too cold; emergency repairs to homes (windows, roofs, doors); blankets and warm clothing store.
9. Welcome and Safety LeadWelcome GroupThe welcome desk and newcomer cards; buddies for newcomers; meeting outside groups (the welcome protocol, section 12.10); calming conflict; night watch rota and log; signals (whistles); safeguarding with the Children and Learning Lead.
10. Children and Learning LeadLearning GroupChildcare rota so parents can work; a daily routine for children (lessons, play, rest); age-suitable jobs and responsibilities for children and young people; skill-sharing classes for adults (first aid, water treatment, generator use); safeguarding.
11. Wellbeing and Community Life LeadWellbeing GroupDaily check-ins on people living alone; company for older people; peer support for people struggling (with the Care Group); faith and cultural needs; bereavement support; shared meals, music and celebrations that keep morale up; noticing tension early and bringing people together.
12. Logistics and Transport LeadLogistics GroupCarrying water and supplies (trolleys, wheelbarrows, cargo bikes); bicycles and repairs; vehicles and fuel use by agreed rules; the shared tools library; building and repair crews (water station, stands, latrines, shelters); moving people who cannot walk.

Small streets combine roles (for example one person leading Food and Water, or Wellbeing with Care); large streets and neighbourhoods split them. Every role holder chooses a deputy, so no group depends on one person. Every working group meets for ten minutes after the morning briefing, keeps its own log, and reports in one minute at the next briefing.

Roles for everyone: how it works in practice

Rapid organising: first 72 hours

WhenMilestone
Hour 1First Hour card done in every home. Buddies have checked every vulnerable person.
Hours 1 to 3First street meeting at the agreed place and time, or 08:00 if that time falls at 21:00 or later, or earlier than 07:00 (section 12.6). Charter adopted. Interim role holders chosen for all twelve roles. Every person present joins a working group.
Hours 3 to 12Street links make contact with each neighbouring street. Water filled and protected. Dry toilets ready in every home. Warm room open if it is cold. Census cards collected.
Day 2Every working group has a list of specific responsibilities and owners. Water station, charging station and notice board running. Night watch rota in place.
Day 3First community meeting: direct elections for all roles. Neighbourhood council meets for the first time.
STREET ASSEMBLY every resident 16+ · one vote each · paper ballot elects and can recall each role directly Street Coordinator safety · outside relations Records and Resources shared stores · ledger Household delegates one chosen by each household Water, sanitation Food Health, care Power Comms, network Warmth, shelter Welcome, safety Children, learning Wellbeing Logistics, transport Role holders (each directly elected, each leads a working group in which every member owns a specific responsibility) Every resident joins at least one working group. Dispute Panel: three residents drawn by lot for each dispute. Recall: 25% of the Assembly sign = powers suspended until a recall vote · 50% sign = role ends at once
Figure 12.1. How streets govern themselves. The Assembly elects every role directly and can recall any of them at any time.

12.3 Street Charter

The Street Assembly adopts this charter at its first meeting. Read it aloud, then vote by show of hands. It can only be changed later by a vote at a community meeting, announced at least two days before.

Street Charter

  1. Every resident of the street aged 16 or over has one vote. Newcomers who accept this charter and take a role vote from the first community meeting at least a day after they accept it.
  2. The Harm Principle. Each person's freedom over things that concern only themselves is their own. The street may act against someone only to prevent harm to others.
  3. No one is refused water, food, warmth or medical help as a punishment.
  4. Force is used only in immediate self-defence or to protect another person from immediate harm, and never more force than is needed. Check that this agrees with the law on self-defence where you live (in England and Wales, the law on reasonable force).96
  5. Homes and private belongings stay private. Gifts to the shared stores are voluntary and written down. Anything borrowed is recorded and returned.
  6. Children are safeguarded. No child is placed alone in the care of an adult who is not their parent or carer without the parent's or carer's agreement. Children's activities always have two adults present.
  7. Personal records (census cards, medical needs) are private. Only the role holders who need them may read them.
  8. We cooperate with the police, fire and ambulance services, the local authority and the armed forces whenever they are present. Our organisation fills gaps; it does not replace the law.
  9. Everyone has a role, and every role matters: nobody is a gofer. Anyone may step down from a role at any time without blame, and will be offered another. Nobody is treated as a threat; everyone is a possible member.
  10. All votes are by paper ballot, except the first meeting's show of hands. Ballots are counted in public by two people from different households.

12.4 Choosing role holders

Day 1: interim roles

On the first day there is no time for a formal election. At the first meeting, ask for volunteers for each role. If more than one person volunteers, decide by show of hands. These are interim roles that last until the first election, no later than day 3.

Day 3: first election

  1. Announce. At least a day before, post on the notice board and the street network: the date, time and place of the community meeting. All roles are open.
  2. Candidates. Anyone eligible to vote may stand for any role. Each candidate says, in two minutes, what they will do. Candidates may stand for more than one role but may hold only one main role (small streets may agree otherwise).
  3. Returning officer. Draw two residents by lot from residents who are not standing. They run the vote and count.
  4. Ballot. Each voter gets one paper per role (Ballot Paper, form 4) and marks one candidate. The candidate with the most votes wins (as in the national model). A tie is settled by a second vote between the tied candidates; if still tied, by drawing lots.
  5. Count in public. The two returning officers count aloud in front of anyone who wants to watch. Results go in the Decisions Book and on the notice board.

If only one person stands for a role, that person takes it without a ballot. If no one stands, the interim holder continues, and the role is offered again at each community meeting until someone stands. Every open role is posted on the notice board at least a day before the meeting that fills it.

After day 3: cases for roles at community meetings

There are no further elections on a schedule. A role holder keeps the role until they step down, are recalled, or lose a vote at a community meeting. Any member of the Assembly who thinks a role holder is not doing the job well, or who thinks they would do a role better (including someone who holds a different role now), can present their case:

  1. Give notice. Tell the role holder in person first. Then tell the Street Coordinator (for a case about the Coordinator's own role, the Records and Resources Keeper), and post a notice on the notice board and the street network at least a day before the community meeting: which role, and who is standing.
  2. Present the case. At the meeting, the person who brought the case speaks for two minutes: what is not working, and what they would do. The role holder answers for two minutes. Anyone else who wants the role may also stand and speak for two minutes. Speak about the work, not about the person.
  3. Vote. Two returning officers, drawn by lot, run a paper ballot between the role holder and everyone standing, in the same way as the first election. The most votes wins. The result stands only if at least a quarter of the Assembly votes; if fewer vote, the role holder keeps the role.
  4. Afterwards. Everyone is thanked. Whoever does not hold the role after the vote keeps their other responsibilities or is offered a new one: nobody is left without a role. If the winner held another role, their deputy takes it over, and the next community meeting elects its holder in the same way. The same person may not bring a case for the same role again within 14 days (a recall petition is always possible).

Recall: removing role holders at any time

When roles are too hard

A crisis is exhausting. Someone elected on day 3 may be struggling by day 10. This is normal and is not a failure.

12.5 Making street rules: weighted vote

Role holders make day-to-day decisions within their own area, as a minister runs a department. In an emergency they act first and report at the next briefing. An emergency action ends after 48 hours unless a weighted vote confirms it. That vote may be held straight after the 10:00 briefing, by paper ballot of the four groups, if it was announced at the briefing before. Any street rule that will last more than 7 days, or that affects everyone (for example, rationing, agreed quiet hours, sharing rules), must pass a weighted vote, as in the national model. Street rules bind only those who accept the Street Charter. They cannot override the law or the rights of people who have not agreed, and they cannot restrict anyone's lawful use of a public road.

The role holder whose area the rule falls in proposes it. Four groups then vote separately, and each group gives its whole weight to the side its majority chose:

GroupWeightHow it decides
The lead role holder (the proposer)30%Yes, by proposing it (and may withdraw it)
All the other role holders20%Majority of them
Household delegates (one per household)25%Majority of households
The Assembly's direct vote25%Majority of residents voting

A rule passes with more than 50%. So a rule passes if the proposer is backed by either the households or the Assembly (30 + 25 = 55). The proposer and the other role holders alone cannot pass a rule (30 + 20 = 50, not more than 50). Within each group, a tie counts as "no". This keeps power with the residents while letting role holders lead.

Residents' initiative. Residents do not have to wait for a role holder. Any proposal signed by 10% of the Assembly goes to the weighted vote at the next community meeting. The role holder for that area casts the 30% according to their own vote; if no role holder covers it, the 30% is decided by the Assembly's majority.

Rules that cross working groups. If a proposed rule touches more than one working group (for example, giving stored water to the shared kitchen touches both Water and Food), the Rules Adjudicator decides whether it needs co-sponsors. The leads of the groups affected then propose it together and vote as one: their combined weight stays 30%, or rises to 40% if half or more of all role holders co-sponsor it.97 One role holder who covers several areas still holds 30%. The national model does not say where the extra 10% comes from; in the street version it comes from the other role holders' share, which falls to 10%, so the weights still add up to 100%.

Household delegates. Each household chooses its own delegate by its own agreement, and tells the Records and Resources Keeper. If it cannot agree, the delegate is drawn by lot among its adults.

Worked example. The Water Lead proposes: "Each person may take 10 litres of treated water a day from the street station. No garden watering." Most other role holders vote yes (20). Most households vote yes (25). Most residents vote yes (25). Total: 30 + 20 + 25 + 25 = 100%. The rule passes. If instead most households and most residents had voted no, the total would be 30 + 20 = 50%, and the rule would fail.

A rule that clearly conflicts with the Harm Principle can be challenged by any resident. The Dispute Panel gives an opinion before the vote, and the proposer must answer it in front of the Assembly. In the street version, the Panel advises; the Assembly decides.

12.6 Running your first meeting

Aim for 45 minutes. Stand in a circle if outdoors. Bring this guide, the Household Cards, pens, the Role Board and a whistle.

  1. Welcome (3 min). Introduce yourself and say why you called the meeting. Keep calm and practical.
  2. What we know (5 min). What has happened, what the radio says, how long it might last. Say clearly what is unknown.
  3. Urgent needs (5 min). Anyone in danger now? Anyone on medical equipment, without heat, or alone? Act on these first.
  4. The Charter (5 min). Read the Street Charter. Vote by show of hands.
  5. Interim roles (10 min). Ask for a volunteer for each role, and for an interim Rules Adjudicator (a resident with no other role). Write them on the Role Board.
  6. Working groups (5 min). Everyone else joins a working group and is given a specific responsibility by its interim lead. Seated responsibilities for those who need them. Nobody leaves without one.
  7. The census (5 min). Hand out Household Cards. Collect them by the evening meeting.
  8. Today's tasks (5 min). Each interim lead says what their team will do before the evening meeting.
  9. Next meetings (2 min). Daily briefing at 10:00 and check-in at 18:00. First community meeting, with the first election: day 3.

12.7 Daily rhythm

12.8 Sharing fairly: rules for shared stores

The economist Elinor Ostrom won the Nobel Prize for showing how communities manage shared resources well without either a central authority or private ownership. Her findings translate into simple rules for the street's shared stores:98

  1. Clear boundaries. Everyone knows what is in the shared store and who may draw on it.
  2. Rules that fit. Rules match real conditions (how much water there is, how many people).
  3. Those affected make the rules. Through the weighted vote.
  4. Open records. The ledger is open to every resident. Two people sign for every issue from the store.
  5. Gentle, rising responses. A first breach gets a quiet word, a second a public reminder, a third goes to the Dispute Panel. Never withhold water, food, warmth or medical help (Charter rule 3, section 12.3).
  6. Quick, cheap disputes. The Dispute Panel meets the same day.
  7. Recognised by authorities. We tell the local authority and the police what we are doing as soon as we can.
  8. Layers. Street stores sit within neighbourhood arrangements.

Keep shared stores in two or three separate places, so that one loss (fire, theft) is not a disaster.

12.9 Growing outward: street, neighbourhood, area

The model starts with one street and grows by invitation. The same rules apply at each level: direct election of role holders, recall at any time, weighted votes, the Harm Principle.

Our street 20 to 80 homes Neighbourhood 5 to 15 streets Area / ward StStStSt How it grows 1. Our street organises. 2. Two people visit the next street, bring the guide, help their first meeting. 3. Each street sends its Coordinator and one elected delegate to the Neighbourhood Council. 4. All residents of member streets directly elect neighbourhood roles. 5. Repeat for the wider area.
Figure 12.2. Growth by invitation. Each level uses the same rules.

At neighbourhood level, the weighted vote uses the same four groups, with street delegates in place of household delegates: the proposing neighbourhood role holder 30%, other neighbourhood role holders 20%, street delegates 25%, residents' direct vote 25%. This mirrors the national model, with street delegates playing the part of constituency MPs.

The neighbourhood council handles what one street cannot: sharing a Starlink link, a large water source, a medical post, contact with authorities, and help for streets in trouble.

The council meets weekly at an agreed place and time. Each street elects its neighbourhood delegate in the same way as its role holders. Cases and recalls for neighbourhood roles are presented at the council; residents then vote by paper ballot at their own street's next community meeting, and each street's returning officers send the count to the council.

12.10 Welcome is our defence: outsiders and roaming groups

In a long crisis, people will arrive: relatives, people whose homes are unsafe, people from areas that are worse off, and possibly groups looking for food, some of them aggressive. Our first defence is not walls or weapons. It is an offer: join us, take a role, share the work and the stores, and have a vote. People with a role, food and a place to belong are much less dangerous than people with nothing to lose. A community that grows gains hands, skills and safety.

Signals (agree these in advance)

WhistleMeaning
One long blastAttention: come to the meeting point. (Visual signal: a flag or sheet at the meeting point by day; a torch waved in circles by night.)
Three short blasts, repeatedHelp needed here (injury, fire, someone in trouble).
Repeated short and long blasts, without stoppingDanger: go inside, lock doors, stay away from windows.

Newcomers (individuals and families)

  1. A member of the welcome team greets them. Offer water first.
  2. Listen to their situation. Note any urgent medical need and call the Health and Care Lead.
  3. Explain the Street Charter and the offer: a role, a fair share, a vote from the next community meeting.
  4. If they accept, fill in a Newcomer Card, give them a buddy for the first days, and a role the same day.
  5. Housing: only in homes whose owners or occupants agree.
  6. If the street runs a community app, a role holder vouches for the newcomer at the welcome desk, and an administrator then approves the account.

Groups, including aggressive ones

  1. Alert calmly. The Welcome and Safety Lead and two or three trained members go to meet the group at the edge of the street, in the open, in daylight if possible. Never alone. Others watch from a distance and stay ready to raise the alarm.
  2. Open with the offer. Hands visible, calm voice. "You're welcome here. We have water we can share, and we're organising together. If you want to stay, there's a role and a vote for you."
  3. Give something at once. Water. It shows good faith and lowers tension.
  4. Listen. What do they need? Where are they from? Who is hurt or ill?
  5. Explain the terms (the Charter). Roles are given quickly, and preferably responsible ones (carrying water, night watch, building). People with work and responsibility rarely cause trouble.
  6. If they leave, let them go with water. Tell the neighbourhood council.
  7. If they threaten violence, do not fight over things. Things can be replaced; people cannot. Sound the danger signal, withdraw, lock doors, protect people. Note descriptions. Warn neighbouring streets. Report to the police as soon as possible.
Warning. Do not carry or use weapons to confront anyone. The law where you live sets the limits of self-defence. In UK law, for example, you may use reasonable force (the details differ in Scotland and Northern Ireland) to defend yourself or others from immediate harm, but not to punish, chase or take revenge.99 Escalation gets people killed. The aim is that everyone on our street, and everyone who comes to it, stays alive.

Night watch

Pairs, two-hour shifts, a whistle each, a torch, a notebook. Walk the street slowly, visibly and in a friendly way. Look for fires, people in distress, carbon monoxide danger (someone running a generator indoors) and strangers who may need help. Log anything unusual for the 10:00 briefing.

12.11 Disputes

For any dispute that people cannot settle themselves, draw three residents by lot from residents who are not involved. The Panel hears both sides the same day, decides, and records the decision in the Decisions Book. Either side may appeal to the Assembly at the next community meeting.

12.12 Street records

Printable versions of every form are in printables/Street Forms.html (list in Appendix C).

Notes

  1. Sense Future, "Sovereignty" (the Sovereignty model: directly elected ministers, recall, weighted voting, regular voting days). https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  2. Sense Future, "Sovereignty" (the Sovereignty model: directly elected ministers, recall, weighted voting, regular voting days). https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  3. Sense Future, "The Sovereignty Act" (Draft Sovereignty Act 2025) and "Harm Principle". https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  4. Sense Future, "The Sovereignty Act" (Draft Sovereignty Act 2025) and "Harm Principle". https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  5. Sense Future, "The Sovereignty Act" (Draft Sovereignty Act 2025) and "Harm Principle". https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  6. Criminal Justice and Immigration Act 2008, section 76, "Reasonable force for purposes of self-defence etc." (England and Wales). https://www.legislation.gov.uk/ukpga/2008/4/section/76 (accessed 14 November 2026). Back to text
  7. Sense Future, "Sovereignty" (the Sovereignty model: directly elected ministers, recall, weighted voting, regular voting days). https://sensefuture.org/sovereignty (accessed 14 November 2026). Back to text
  8. E. Ostrom, Governing the Commons: The Evolution of Institutions for Collective Action, Cambridge University Press, 1990. Back to text
  9. Criminal Justice and Immigration Act 2008, section 76, "Reasonable force for purposes of self-defence etc." (England and Wales). https://www.legislation.gov.uk/ukpga/2008/4/section/76 (accessed 14 November 2026). Back to text

Chapter 13Water and sanitation in detail

Water is the most urgent physical need after warmth. Dirty water and poor hygiene are the most common cause of illness and death after disasters. This chapter covers how much you need, where to find it in and around a normal home, how to make it safe with things nearly everyone has, and how to manage toilets and handwashing without running water. Methods go from the simplest (no equipment) to the best (bought filters and group stations).

13.1 How much water

UsePer person per daySource
Drinking, minimum3 litres (much more in hot weather; more in illness, pregnancy, breastfeeding, hard work)UK Government; WHO survival minimum 2.5 to 3 litres100101
Drinking, cooking and basic hygieneAbout 10 litresWHO102
All needs in a long emergency15 litres minimumSphere humanitarian standard103

A street of 50 homes with 120 people needs at least 360 litres of safe drinking water every day, and around 1,800 litres for all needs. Plan for this.

13.2 Where water is hiding in your home

Most people do not know how much water is already stored inside their house.

A B C D E F A Cold water tank in the loft 100 to 230 litres (homes with a hot water cylinder). Boil, or filter + chlorine. B Hot water cylinder 100 to 210 litres (not combi boilers). Boil, or filter + chlorine. C Bath filled as soon as the power goes: 100 to 200 litres. Cover it. Boil, or filter + chlorine. D Toilet cistern (the tank, not the bowl): 6 to 13 litres. Boil, or filter + chlorine. E Water in the pipes: close the stopcock, open the lowest tap. Boil, or filter + chlorine. F Water butt: 100 to 200 litres of rainwater. Boil, or filter + chlorine. Plus: kettle, pans, bottles, buckets, ice in the freezer (not hot water bottles). Filter = 0.1 micron or certified for cysts.
Figure 13.1. Stored water in a typical home. A home with a loft tank (common in the UK) and a hot water cylinder may hold a few hundred litres (other homes store water differently, for example in a rooftop tank or a water heater tank: treat that water as open water too; a common loft tank holds 227 litres) before anyone fills a bath.

13.3 Other sources around you

Warning. Boiling, bleach and filters do not remove fuel, oil, chemicals, pesticides or heavy metals. Do not drink floodwater, water with an oily sheen or chemical smell, or water from near industrial sites, busy roads or car parks. Distilling does not make them safe either: fuel and solvents boil off with the steam and collect in the clean bowl, and heating fuel-contaminated water can start a fire. Find another source.109110

13.4 Making water safe: decision chart

First: where is the water from?Mains cold tap before pressure loss (flats: ask): any method below, or none if stored clean and covered.All other water: boil, or filter + chlorine. Sun only as a last resort. Could it contain fuel or chemicals? (floodwater, oily sheen, chemical smell) Yes Do not drink.Find another source. No Is it cloudy, coloured or full of bits? (cannot read print through a bottle of it) Yes Clear it first 1. Let it settle for some hours, pour off. 2. Strain through cloth or a coffee filter. No (clear) Now kill the germs (top box decides which): BOIL (best)Rolling boil for1 minute. Cool,keep covered. TABLETSMains only, or after0.1 micron/certifiedfilter. 30 min. BLEACHAs tablets. 5%:2 drops a litre(4 if cloudy). 13.5 SUNLIGHTClear bottle, fullsun 6 hours.Last resort.
Figure 13.2. Making water safe. Clear it first, then kill the germs. Wait 30 minutes after tablets or bleach. Chlorine dioxide tablets do not replace boiling or a 0.1 micron filter for open water. A bought 0.1 micron hollow-fibre filter, or one certified for cyst removal (section 13.7), followed by tablets or bleach, makes open water safe; clear cloudy water first to protect it. After any other filter, boil the water.
Warning: rivers, canals, ponds, reservoirs, roof rain and water butts. Chlorine (bleach or tablets) does not reliably kill Cryptosporidium, a parasite common in open water, and works slowly against Giardia in cold water. For water from any of these sources, boil it, or filter it through a hollow-fibre filter of 0.1 micron (or a filter certified for cyst removal) and then chlorinate it.111 Chlorine dioxide tablets act slowly and not reliably against Cryptosporidium: for open water they do not replace boiling or a 0.1 micron filter. Chlorine alone is enough only for water from a tap fed straight from the mains, drawn before any loss of pressure; in a home with a loft tank, that is usually only the kitchen cold tap. In flats it may be no tap at all (section 18.8).112 Water from the loft tank, the hot water cylinder, the bath, any toilet cistern, water drained from the pipes, and tap water after the pressure returns, also counts as open water. Rainwater from roofs, gutters, downpipes and butts counts as open water too, because bird and animal droppings wash into it. Mains water drawn before pressure loss and stored in clean, covered containers is safe to drink as it is (replace it every 6 months).113114

13.5 Methods, step by step

Tablets and bleach alone are only for mains cold-tap water drawn before pressure loss (section 13.4); for all other water, boil it, or filter it through a 0.1 micron filter (or one certified for cyst removal) first.

Method 1: Boiling (best method)

  1. If the water is cloudy, clear it first (section 13.6).
  2. Bring it to a rolling boil (big bubbles that do not stop when stirred) and keep it boiling for 1 minute.115
  3. Let it cool with a lid on. Store it in a clean, covered container.
  4. To improve the flat taste, pour it back and forth between two clean containers.

What you can boil on: a gas hob (it can still be used in a power cut; light it with a long match on the lowest setting if the electric igniter does not work)116, a camping stove, a barbecue or a wood fire (all outdoors only), or a brick rocket stove (Chapter 19). Boiling uses a lot of fuel. For large amounts of other water, a 0.1 micron filter (or one certified for cyst removal) followed by chlorine saves fuel (section 13.7). Chlorine alone is only for mains cold-tap water drawn before pressure loss.

Method 2: Chlorine tablets

Tablets of sodium dichloroisocyanurate (for example Puritabs, Aquatabs) or chlorine dioxide (for example Micropur MP1; not "Micropur Classic", which uses silver and does not disinfect) give an exact dose. Follow the packet: usually one tablet for a stated number of litres, wait 30 minutes (longer if the water is very cold). Chlorine dioxide tablets act slowly and not reliably against Cryptosporidium: for open water they do not replace boiling or a 0.1 micron filter (section 13.4). They are the easiest method for most people. Buy them now: they keep for years.117

Method 3: Household bleach

Bleach is in most homes and works well, if it is the right kind and the dose is right.

  1. Check the label. Use bleach whose only active ingredient is sodium hypochlorite (sodium hydroxide may also be listed; that is normal). Do not use bleach with perfume, "thick" formulas with detergents or surfactants, "splashless", "colour-safe" or any added cleaner. Cheap supermarket "thin bleach" is often suitable; read the label. Strengths vary. If the label gives the strength, adjust the table: drops per litre = 2 × 5 ÷ the strength in % (for example 4 drops per litre for 2.5% bleach). If the label says only "less than 5%", or gives no strength, use tablets or boil instead.118
  2. If you only have thick or scented bleach, boil instead.
  3. Measure using the table below. A medicine dropper, or the oral syringe that comes with children's medicine, is ideal.
  4. Stir and wait 30 minutes, covered.
  5. Smell it. It should smell faintly of chlorine, like a swimming pool. If it does not, add the same dose again and wait another 15 minutes. If it smells very strong, leave it uncovered for a few hours or pour it between containers.
Volume of water (5% bleach)Clear waterCloudy or very cold water (after clearing)
1 litre2 drops4 drops
2 litres (a large drinks bottle)4 drops8 drops
10 litres (a bucket)1 ml (20 drops)2 ml
20 to 25 litres (a jerrycan)2.5 ml (half a teaspoon)5 ml (one teaspoon)
50 litres5 ml (one level teaspoon)10 ml
200 litres (a water butt or barrel)20 ml (four teaspoons)40 ml

These doses follow US CDC and EPA emergency guidance (about 8 drops of 5 to 9% bleach per US gallon, double for cloudy water).119120 One drop is about 0.05 ml. For other strengths, use the rule above. Bleach slowly loses strength once opened; use a bottle less than a year old where possible. If you have swimming pool or hot tub test strips, aim for a free chlorine reading of 0.5 to 2 mg/l after 30 minutes.121

Warning. Never mix bleach with other cleaners, especially those containing ammonia or acids (some toilet cleaners, descalers): this releases toxic gas.122 Store bleach out of reach of children. Measure carefully: more is not better.

Method 4: Sunlight (SODIS)

Solar disinfection, developed by the Swiss research institute Eawag and recognised by the World Health Organization, uses the sun's ultraviolet light and heat.123

  1. Use clear plastic drinks bottles (PET, the usual fizzy drink or water bottle), up to 2 litres. Remove labels. Do not use coloured or scratched bottles.
  2. The water must be fairly clear: you should be able to read large print through the full bottle. If not, clear it first.
  3. Fill the bottle, cap it, shake for 20 seconds, then top it up fully.
  4. Lay it flat in full sun (on a roof, a sheet of metal or a pale surface) for 6 hours. If more than half the sky is cloudy, leave it for 2 full days.124
  5. Drink straight from the bottle.

Far from the equator, treat SODIS as a last resort. It was developed for sunny regions much closer to the equator; at high latitudes such as Britain's the sun is often too weak, and in winter it does not work. Use it only when you cannot boil, or filter (0.1 micron or certified) and then chlorinate.125

13.6 Clearing cloudy water, and distilling

Clearing does not make water safe by itself, but it makes boiling, chlorine and sunlight work properly, and it protects filters.

Settle and pour (no equipment)

Fill a bucket and leave it undisturbed for several hours, or overnight. Gently pour the top water into a second clean container, leaving the sludge behind.

Cloth filter

Fold a clean cotton cloth (tea towel, T-shirt, pillowcase) four to eight times. Pour the water through it into a clean container. In a study in Bangladesh, filtering through old cotton sari cloth folded four to eight times cut cholera cases by about half, because it removed the tiny creatures that carry the bacteria.126 Coffee filters and kitchen paper also work for small amounts.

Bottle or bucket sand filter

Dirty water poured in gently(pour onto a plate or cloth to avoid digging holes) Cloth layer Fine sand, washed: the thickest layer, at least 10 cm(play sand, builders' sharp sand) Coarse sand or crushed charcoal from a wood fire(never barbecue briquettes) Gravel or small stones, washed(aquarium gravel, garden gravel) Cloth over the outlet Then boil it, or 0.1 micron filter + chlorine. Container: a 2-litre drinks bottle with the bottom cut off, held upside down; or a bucket with small holes in the base.
Figure 13.3. Homemade sand filter. It clears water and removes some germs, but it does not make water safe on its own. Afterwards, boil the water, or pass it through a 0.1 micron filter and then add tablets or bleach.

Wash the sand and gravel first in several changes of water until the water runs nearly clear. Throw away the first few litres that come through. When the flow slows, scrape off and replace the top centimetre of sand.

Distilling (only for salty water)

Put the water in a large pan. Place a heatproof bowl in the middle of the pan (standing on a small heatproof stand or a few clean stones, so its rim sits well above the water). Put the pan's lid on upside down, so its handle points down over the bowl. Put ice or cold water on top of the lid if you can. Simmer. Steam rises, condenses on the cold lid, runs to the handle and drips into the bowl. The bowl collects clean water and the salt stays behind. It is very slow (a pan still makes only a small cup of water an hour) and uses a lot of fuel. Use it only for salty water when you have no other source. Never distil water that smells of fuel, oil or chemicals: they pass over with the steam, and the vapour can catch fire.

13.7 Bought filters: best value

Hollow-fibre filters (for example the Sawyer Squeeze, about 30 to 45 GBP; pores about 0.1 micron) and ceramic or gravity filters (about 0.2 to 0.5 micron) remove bacteria and parasites, and, as their makers state, can treat thousands of litres if back-flushed as the instructions say. Most do not remove viruses.127 For open water, add tablets or bleach only after a 0.1 micron hollow-fibre filter or a filter certified for cyst removal. After any other filter (a ceramic or gravity filter without that certificate, or a jug or carbon filter), boil the water. Do not let hollow-fibre filters freeze once wet: ice cracks the fibres and makes them useless without any visible sign. Keep them indoors in winter.

Two-bucket ceramic filter for a home. Stack two food-grade buckets with lids. Fit one or two ceramic filter candles (bought for about 15 to 30 GBP each) through holes in the bottom of the top bucket, and a tap near the bottom of the lower bucket. Pour settled water into the top bucket; clean water collects below at about 1 to 4 litres an hour per candle. Ceramic candles remove bacteria and parasites but not all viruses. If the candle is certified for cyst removal, add tablets or bleach to the output. If it is not certified, boil the output. Scrub the candles gently when the flow slows.128

13.8 Street water station

Once the outage lasts more than a few days, it is safer and cheaper in fuel to treat water centrally. The Water Lead runs this station.

1 COLLECTrain, butts,river (raw) 2 SETTLE12 to 24 hours;draw from above sludge 3 FILTER0.1 micron or certified(or boil instead) 4 CHLORINATEmeasured dose,wait 30 minutes 5 SERVEtap intocleancoveredcontainers
Figure 13.4. Street water station built from water butts, food-grade barrels or 1,000-litre IBC tanks. Label the raw and treated containers clearly and never let them touch the same scoop.

13.9 Storing water

13.10 Toilets without water

If water is scarce or sewers back up, stop flushing. A dry toilet is safe and, done properly, does not smell much.

Two-bucket toilet (best for homes)

Separating urine from faeces makes home toilets safer and less smelly; emergency managers in New Zealand give this method as standard advice.135

Bucket 1: WEE lid on between uses Bucket 2: POO lined with 2 strong bags Bucket 1 (wee): pour onto garden soil away from food, or a drain if sewers work. Rinse with a little water. Bucket 2 (poo): after each use cover with a cupful of sawdust, soil, cat litter, shredded paper or dry leaves. Lid on. When three-quarters full, tie the bags, put in a lidded bin outside, away from the house and any water source.
Figure 13.5. Two-bucket toilet. Toilet paper goes in bucket 2. Wash hands every time.

No second bucket? Empty the toilet bowl (scoop out the water), put two strong bin bags inside it, sit on the normal seat, and use cover material after each use. Tie off and replace as above.

Group toilets (longer outages)

Dig a trench latrine about 30 cm wide and up to 1 metre deep (stop well above any water you meet when digging) in a garden or open ground, at least 30 metres from any well, stream, water butt or water station, and downhill from them.136 Cover each use with soil. Provide a screen for privacy, a handwashing point, and a lid or board. Fill in when the waste is 30 cm from the top. Plan one latrine for every 20 people.137138 Most town gardens cannot give 30 metres: where they cannot, do not dig; use two-bucket toilets and the street waste point in section 13.13 instead.

13.11 Handwashing: tippy tap

Handwashing with soap after the toilet and before handling food prevents a large share of the illness that follows disasters.139 When there is no soap, use an alcohol hand rub (at least 60% alcohol), or rub hands well under poured water alone. WHO and UNICEF do not recommend ash, sand or soil, because they can be contaminated; use them only as a last resort.140

Container: a 2 to 5 litre plastic bottle or jerrycan, hung by its handle or neck from a stick. Hole: one small hole (a hot nail) near the cap, on the side facing you. Foot pedal: a stick tied by string to the cap end. Press with your foot: the bottle tips, water trickles out. Soap on a string, or in a mesh bag. Gravel underneath so the ground does not get muddy.
Figure 13.6. Tippy tap: it uses a fraction of a tap's water, and no hand touches the container.

13.12 Diarrhoea and dehydration

Diarrhoea kills through dehydration, especially in babies, young children and older people. Start oral rehydration at the first sign.

Home oral rehydration solution (World Health Organization recipe)

Into 1 litre of safe water, stir 6 level teaspoons of sugar and half a level teaspoon of salt141 until dissolved. Sip often, a little at a time.142 Make a fresh batch each day. Keep breastfeeding babies and keep feeding children with diarrhoea.

Get urgent help (Health and Care Lead, or the emergency number if phones work) for: peeing much less than normal or very dark urine (a baby: fewer wet nappies), dizziness on standing that does not go away, fast breathing or fast heartbeat, unusual tiredness or a drowsy child, few or no tears in a child, or a baby with a sunken soft spot on the head. Emergency: blue, grey, pale or blotchy skin, cold skin, difficulty breathing, confusion, or very hard to wake.143

13.13 Rubbish, toilet waste and pests

When bin collections stop for weeks, rubbish and sealed toilet bags become a health risk and attract rats and flies. The Water and Sanitation Lead runs a street waste point:

Notes

  1. UK Government, "Get prepared for emergencies", Be Ready campaign, GOV.UK, 2025 to 2026. https://beready.campaign.gov.uk/get-prepared-for-emergencies (accessed 14 November 2026). Back to text
  2. World Health Organization, Guidelines for Drinking-water Quality, fourth edition incorporating the first and second addenda, 2022. https://www.who.int/publications/i/item/9789240045064 (accessed 14 November 2026). Back to text
  3. World Health Organization, Guidelines for Drinking-water Quality, fourth edition incorporating the first and second addenda, 2022. https://www.who.int/publications/i/item/9789240045064 (accessed 14 November 2026). Back to text
  4. Sphere Association, The Sphere Handbook: Humanitarian Charter and Minimum Standards in Humanitarian Response, fourth edition, 2018 (water supply standard 2.1). https://spherestandards.org/handbook/ (accessed 14 November 2026). Back to text
  5. Drinking Water Inspectorate, "Water storage tanks and cisterns" (in many older homes only the kitchen cold tap comes straight from the mains; other taps are fed from a storage tank). https://www.dwi.gov.uk/consumers/learn-more-about-your-water/water-storage-tanks-and-cisterns/ (accessed 14 November 2026). Back to text
  6. Texas A&M AgriLife Extension, "Pre-storage treatment" (first-flush diverters for rainwater). https://rainwaterharvesting.tamu.edu/pre-storage-treatment (accessed 14 November 2026). Back to text
  7. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  8. Ofwat, "Supply interruptions" (alternative supply of at least 10 litres per person per day). https://ofwat.gov.uk/households/supply-and-standards/supply-interruptions/ (accessed 14 November 2026). Back to text
  9. Priority Services Register (energy and water companies), thepsr.co.uk. https://www.thepsr.co.uk/ (accessed 14 November 2026). Back to text
  10. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  11. US Environmental Protection Agency, "Emergency Disinfection of Drinking Water". https://www.epa.gov/ground-water-and-drinking-water/emergency-disinfection-drinking-water (accessed 14 November 2026). Back to text
  12. US Centers for Disease Control and Prevention, "About Water Treatment Options When Hiking, Camping, or Traveling" (filters of 1 micron or smaller against Cryptosporidium; chlorine is not effective against it). https://www.cdc.gov/drinking-water/prevention/water-treatment-hiking-camping-traveling.html (accessed 14 November 2026). Back to text
  13. Drinking Water Inspectorate, "Water storage tanks and cisterns" (in many older homes only the kitchen cold tap comes straight from the mains; other taps are fed from a storage tank). https://www.dwi.gov.uk/consumers/learn-more-about-your-water/water-storage-tanks-and-cisterns/ (accessed 14 November 2026). Back to text
  14. Drinking Water Inspectorate, "Water storage tanks and cisterns" (in many older homes only the kitchen cold tap comes straight from the mains; other taps are fed from a storage tank). https://www.dwi.gov.uk/consumers/learn-more-about-your-water/water-storage-tanks-and-cisterns/ (accessed 14 November 2026). Back to text
  15. US Centers for Disease Control and Prevention, "How to Create and Store an Emergency Water Supply" (cleaning containers; replace stored water every 6 months). https://www.cdc.gov/water-emergency/about/how-to-create-and-store-an-emergency-water-supply.html (accessed 14 November 2026). Back to text
  16. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  17. Which?, "What to do in a power cut" (gas boilers need electricity; gas hobs can be lit with a match). https://www.which.co.uk/reviews/energy-companies/article/power-cuts/what-to-do-in-a-power-cut-aVPIj7v1DXsA (accessed 14 November 2026). Back to text
  18. Aquatabs, "Frequently asked questions" (five-year shelf life in strip packs). https://www.aquatabs.com/faq/ (accessed 14 November 2026). Back to text
  19. US Environmental Protection Agency, "Emergency Disinfection of Drinking Water". https://www.epa.gov/ground-water-and-drinking-water/emergency-disinfection-drinking-water (accessed 14 November 2026). Back to text
  20. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  21. US Environmental Protection Agency, "Emergency Disinfection of Drinking Water". https://www.epa.gov/ground-water-and-drinking-water/emergency-disinfection-drinking-water (accessed 14 November 2026). Back to text
  22. World Health Organization, "Guidelines for drinking-water quality", fourth edition incorporating the first and second addenda, 2022 (free chlorine residual of at least 0.5 mg/l after 30 minutes). https://www.who.int/publications/i/item/9789240045064 (accessed 14 November 2026). Back to text
  23. US Environmental Protection Agency, "Emergency Disinfection of Drinking Water". https://www.epa.gov/ground-water-and-drinking-water/emergency-disinfection-drinking-water (accessed 14 November 2026). Back to text
  24. SODIS (Helvetas), "Application of the SODIS method" (at least 6 hours in full sun; 2 days if more than half the sky is cloudy). https://www.sodis.ch/methode/anwendung/index_EN.html (accessed 14 November 2026). Back to text
  25. SODIS (Helvetas), "Application of the SODIS method" (at least 6 hours in full sun; 2 days if more than half the sky is cloudy). https://www.sodis.ch/methode/anwendung/index_EN.html (accessed 14 November 2026). Back to text
  26. SODIS (Helvetas), "Application of the SODIS method" (at least 6 hours in full sun; 2 days if more than half the sky is cloudy). https://www.sodis.ch/methode/anwendung/index_EN.html (accessed 14 November 2026). Back to text
  27. R. R. Colwell and others, "Reduction of cholera in Bangladeshi villages by simple filtration", Proceedings of the National Academy of Sciences 100(3), 1051 to 1055, 2003. https://doi.org/10.1073/pnas.0237386100 (accessed 14 November 2026). Back to text
  28. US Centers for Disease Control and Prevention, "About Water Treatment Options When Hiking, Camping, or Traveling" (filters of 1 micron or smaller against Cryptosporidium; chlorine is not effective against it). https://www.cdc.gov/drinking-water/prevention/water-treatment-hiking-camping-traveling.html (accessed 14 November 2026). Back to text
  29. CAWST (Centre for Affordable Water and Sanitation Technology), household water treatment resources (ceramic and biosand filters). https://resources.cawst.org/ (accessed 14 November 2026). Back to text
  30. US Centers for Disease Control and Prevention, "How to Make Water Safe in an Emergency". https://www.cdc.gov/water-emergency/about/ (accessed 14 November 2026). Back to text
  31. US Environmental Protection Agency, "Emergency Disinfection of Drinking Water". https://www.epa.gov/ground-water-and-drinking-water/emergency-disinfection-drinking-water (accessed 14 November 2026). Back to text
  32. Texas A&M AgriLife Extension, "Pre-storage treatment" (first-flush diverters for rainwater). https://rainwaterharvesting.tamu.edu/pre-storage-treatment (accessed 14 November 2026). Back to text
  33. CAWST (Centre for Affordable Water and Sanitation Technology), household water treatment resources (ceramic and biosand filters). https://resources.cawst.org/ (accessed 14 November 2026). Back to text
  34. US Centers for Disease Control and Prevention, "How to Create and Store an Emergency Water Supply" (cleaning containers; replace stored water every 6 months). https://www.cdc.gov/water-emergency/about/how-to-create-and-store-an-emergency-water-supply.html (accessed 14 November 2026). Back to text
  35. US Centers for Disease Control and Prevention, "How to Create and Store an Emergency Water Supply" (cleaning containers; replace stored water every 6 months). https://www.cdc.gov/water-emergency/about/how-to-create-and-store-an-emergency-water-supply.html (accessed 14 November 2026). Back to text
  36. Wellington Region Emergency Management Office, "Emergency toilets" (the two-bucket system). https://www.wremo.nz/emergency-toilets/ (accessed 14 November 2026). Back to text
  37. Sphere Association, The Sphere Handbook: Humanitarian Charter and Minimum Standards in Humanitarian Response, fourth edition, 2018 (water supply standard 2.1). https://spherestandards.org/handbook/ (accessed 14 November 2026). Back to text
  38. Harvey, Baghri and Reed, Emergency Sanitation: Assessment and Programme Design, WEDC, Loughborough University, chapter 5 (one toilet per 20 people; at least 30 m from surface water; pit bottoms at least 1.5 m above the water table). https://wedc-knowledge.lboro.ac.uk/resources/books/Emergency_Sanitation_-_Ch_05.pdf (accessed 14 November 2026). Back to text
  39. UNHCR, appendix of Sphere sanitation indicators (a maximum of 20 people per toilet). https://unhcr.org/in/sites/en-in/files/legacy-pdf/49db14bb2.pdf (accessed 14 November 2026). Back to text
  40. WHO and UNICEF, Guidelines on Hand Hygiene in Community Settings, 2025. https://www.pseau.org/outils/ouvrages/unicef_who_guidelines_on_hand_hygiene_in_community_settings_2025.pdf (accessed 14 November 2026). Back to text
  41. WHO and UNICEF, Guidelines on Hand Hygiene in Community Settings, 2025. https://www.pseau.org/outils/ouvrages/unicef_who_guidelines_on_hand_hygiene_in_community_settings_2025.pdf (accessed 14 November 2026). Back to text
  42. World Health Organization Regional Office for the Eastern Mediterranean, guidance on home-made oral rehydration solution. https://applications.emro.who.int/docs/WHOEMCSR594E-eng.pdf (accessed 14 November 2026). Back to text
  43. World Health Organization Regional Office for the Eastern Mediterranean, guidance on home-made oral rehydration solution. https://applications.emro.who.int/docs/WHOEMCSR594E-eng.pdf (accessed 14 November 2026). Back to text
  44. NHS, "Dehydration" (when to get urgent help). https://www.nhs.uk/conditions/dehydration/ (accessed 14 November 2026). Back to text
  45. Harvey, Baghri and Reed, Emergency Sanitation: Assessment and Programme Design, WEDC, Loughborough University, chapter 5 (one toilet per 20 people; at least 30 m from surface water; pit bottoms at least 1.5 m above the water table). https://wedc-knowledge.lboro.ac.uk/resources/books/Emergency_Sanitation_-_Ch_05.pdf (accessed 14 November 2026). Back to text

Chapter 14Electricity in detail, and pedal generator

Without the grid, electricity becomes precious. The things that matter most in a blackout (lights, phones, radios, the street network, some medical devices) need very little power. The things people are used to (heaters, kettles, cookers, washing machines) need far more than any homemade source can give. This chapter starts with the numbers, then covers the power you already have, the car, solar, and how to build a pedal generator from parts found around the street.

14.1 Power and energy figures

Power is measured in watts (W): how fast energy is used. Energy is measured in watt-hours (Wh): a 10 W light on for 3 hours uses 30 Wh. One kilowatt-hour (kWh) is 1,000 Wh.

Typical figures from appliance guides and makers' specifications; the label on your own device gives its real figure.145

What it usesPower or energy
Phone, one full chargeabout 15 Wh
LED torch / LED bulb1 to 3 W / 5 to 9 W
FM radio1 to 3 W
Laptop running10 to 30 W
Wi-Fi router6 to 12 W
Starlink Mini / Standard dish25 to 40 W / 75 to 100 W
CPAP breathing machine30 to 60 W (more with heated humidifier)146
Home oxygen concentratorabout 100 to 350 W for a home model, by model and flow setting (the figure is on its label); choose an inverter or power station rated well above that figure147148
Gas boiler pump and controlsusually under 200 W (the figure is on the boiler's rating plate)
Fridge-freezer0.5 to 1.5 kWh a day
Kettle (boiling 1 litre)2,000 to 3,000 W; about 100 Wh per litre (heating 1 litre by 80°C takes 93 Wh)
Electric heater2,000 W: not practical
What can supply itEnergy
One person pedalling for 1 hourabout 50 Wh (45 to 75)149
Power bank, 20,000 mAhabout 50 Wh usable
Cordless tool battery, 18 V 5 Ahabout 90 Wh
UPS battery, 12 V 7 Ah40 to 80 Wh
Car battery, 60 Ah (to half charge)about 350 Wh
E-bike battery400 to 700 Wh
Portable power station300 to 2,000 Wh
Petrol or diesel car idling, 1 hourup to about 500 Wh (uses roughly 0.5 to 1 litre of fuel)
100 W solar panel, one day in Englandabout 60 Wh in December; 400 Wh in June150
Electric car battery40,000 to 80,000 Wh

What this means: an hour of pedalling charges two or three phones. A car battery can run the street's Wi-Fi router for more than a day. An electric car could charge thousands of phones, or run an oxygen concentrator for several days. Heating, cooking and boiling water must come from gas, wood or other fuel, not from homemade electricity.

14.2 Power you already have

Before building anything, use what is already in the street. Find it with the Asset Door Card (Part 2).

14.3 Cars as generators

The car is the most powerful generator most streets have.

Warning. Run engines only outdoors, at least 6 metres from any door, window or air vent, with the exhaust pointing away from buildings. Never in a garage, even with the door open. Carbon monoxide kills without warning. Never leave a running car unattended.154155 Never refuel with the engine running.

Petrol or diesel car

  1. Park outdoors as above. Turn off the stop-start system (usually a button marked "A" with an arrow), or the engine will keep stopping.
  2. Small loads (phones, laptops): plug USB chargers into the car's 12 V socket or USB ports. A 12 V socket is usually fused at 10 to 15 A, so keep the total below about 120 W.
  3. Larger loads: clip an inverter (12 V to your mains voltage, 230 V in the UK; 300 to 600 W, ideally "pure sine wave") directly to the car battery terminals with short, thick cables (red to +, black to -) and a fuse in the positive cable close to the battery, sized as the inverter maker states, with the engine running. Do not exceed what the alternator can supply at idle: keep to about 500 W.
  4. Charging the street battery: with the engine running, connect the street's 12 V battery to the car with jump leads: red clamp to + on the car battery, other red clamp to + on the street battery, black clamp to - on the street battery, and the last black clamp to bare metal on the car's engine, away from both batteries (so any spark is away from the battery gas). Disconnect in the reverse order. The car charges both. 20 to 30 minutes at a time, with the engine at a fast idle, adds a useful charge. Check the leads do not get hot. This is for lead-acid batteries only: never connect a lithium battery to a car with jump leads; use a DC-DC charger.
  5. Fuel: idling uses roughly 0.5 to 1 litre an hour.156 Running the car for one hour twice a day to charge batteries is far better than idling all day.

Electric cars and hybrids

Prepare now: a gas boiler's electrics need little power (the figure is on its rating plate or in its manual), but most boilers are wired directly into the wall. A registered electrician can fit a plug or a changeover switch so the boiler can run from an electric car, a power station or an inverter. That means central heating in a blackout, if the gas still flows. Test it now, on the supply you plan to use: some boilers will not light on an inverter or a car's V2L socket, because their flame sensor needs a supply whose neutral is earthed. Only the electrician may change the wiring; never improvise an earth link. Do it now if you can.

14.4 Solar power

14.5 Build your pedal generator

A pedal generator turns a bicycle into a charger for a 12 V battery. The battery then charges phones, runs lights, a radio and the street's router. It cannot run heaters, kettles or fridges. One person pedalling at a steady pace produces about 50 W; a short hard effort produces about 100 W.160

The design below uses a friction drive: a small wheel (the "roller") on the shaft of an electric motor presses against the bicycle's back tyre. As you pedal, the tyre spins the motor, and the motor, working backwards, produces electricity. It needs no welding and no special tools.161

1 Bicycle on a standback wheel lifted off the ground 2 Motor with roller pressing on the tyre 3diode fuse 4 12 V batterycar or leisure 5 OutputsUSB car charger, 12 V lights 6 Voltmeter red = positive (+)black = negative (-)
Figure 14.1. Whole system. Pedalling spins the motor through the roller. The diode lets current flow only into the battery. The fuse protects against fire. Phones charge from the battery, not directly from the motor.

What you need, and where to find it

PartBestWhere to find it, or what else works
BicycleAny adult bike with gears and a smooth (road or hybrid) back tyreKnobbly mountain bike tyres work but are noisy and waste energy. Pump the tyre hard.
StandA turbo trainer (indoor cycling stand)Many cyclists own one. Or build the timber stand in Figure 14.2. A bike repair stand also works.
Motor (the generator)A permanent-magnet DC motor with two wires, 12 to 130 V, 100 W or moreSee the motor table below: treadmill motor (best), electric scooter or ride-on toy car motor, car radiator cooling fan motor.
RollerA rubber or polyurethane wheel fixed on the motor shaftA skateboard or scooter wheel; the treadmill motor's flywheel; the motor's sprocket wrapped tightly with strips of old inner tube.
MountA plank, a door hinge, and a bungee cord or springAny scrap timber; hose clips (jubilee clips) or metal strapping to hold the motor.
DiodeSchottky diode, at least 15 A and 45 VInside any old computer power supply (a three-legged part bolted to a metal heat sink, often marked with "30" or "40" and "45" in its code, for example STPS3045 or MBR4045). Keep it on its heat sink. On these three-legged parts the centre leg and the metal tab are the cathode (to the fuse and battery +); the two outer legs are the anodes: join them together and connect them to the motor +. A solar charge controller also blocks back-flow. Or the switch method below.
Charge controller (best)A 12 V solar charge controller (PWM or MPPT), 10 A or more, rated for an input of at least 50 V (many cheap ones accept only about 25 V); with a treadmill motor, 100 V or more (for example a 100 V MPPT controller), because the motor runs unloaded when the battery is full; and drive a treadmill motor from its flywheel, never the small pulley. An MPPT controller needs about 18 to 25 V to start charging: check its start voltage in its manual and choose the gear for it.Often in solar kits, caravans and boats; cheap to buy. Motor to the controller's "PV" input, battery to "BAT". It stops charging at the right voltage by itself, blocks back-flow, and gives protected 12 V and USB outputs. With a controller you need no separate diode. Connect the battery to the controller first, then the motor; disconnect in the reverse order. For a lithium (LiFePO4) battery, the controller must have a lithium setting, chosen before you connect it; never use a lead-acid-only controller with a lithium battery.
Fuse15 A blade fuse in an in-line holderCar accessory shops; spare fuses in the car's fuse box; old car accessory leads.
Battery12 V leisure battery or car batteryA spare car battery; a mobility scooter battery; a UPS battery (small: charge at no more than about 2 A, so pedal gently, and watch the voltage closely); not a lithium battery or a power station unless a charge controller is used (see below).
Wire1.5 mm² copper (red and black), and battery clampsCut from an old mains extension lead (in UK and European cable, the brown and blue cores; colours differ elsewhere, so mark the positive wire with red tape). Jump leads make good battery connections.
VoltmeterA multimeterMany toolboxes have one. Or a cheap plug-in voltmeter for a 12 V socket.
OutputA 12 V socket and USB car chargersA 12 V socket with clips (sold for car accessories), or wire directly to a USB car charger (see step 11, Outputs).
Warning: computer power supplies. The large capacitors inside a computer power supply can hold a dangerous charge (up to about 400 V) for some time after it is unplugged. Unplug it, wait at least 10 minutes, and do not touch the large capacitors or the mains side of the board. Ideally ask a person with electronics experience to remove the diode.

Joining wires without soldering

  • Getting the diode out: with the power supply unplugged and left for 10 minutes, cut the diode's three legs with side cutters as close to the circuit board as you can, so the legs stay long. Leave it on its metal heat sink if you can unscrew the heat sink; it keeps the diode cool. Figure 14.3 shows which leg is which.
  • Screw terminal block (the white plastic connector strip inside old light fittings, or from any hardware shop): push each wire or diode leg into a hole and tighten the screw.
  • Battery clamps: jump leads or the clamps from an old battery charger.
  • Twist and clamp: strip 2 cm of each wire, twist them tightly together, then fix the twist with a small hose clip or a terminal block, and wrap it in electrical tape. Tape alone does not hold.
  • Give every join a gentle pull to test it, and check none of the bare metal can touch another join.

Choosing your motor

You need a permanent-magnet DC motor with two wires. When you spin the shaft by hand, it should feel slightly "notchy" or resistant, and a multimeter on DC volts across the two wires should show a voltage. Motors with three thick wires are "brushless" and need extra parts: avoid them. A car alternator is a poor choice: it needs high speed and uses some of its own power to work.162

MotorWhere it comes fromRoller to use on the tyreNotes
A. Treadmill motor (best)Broken or unused home treadmills: the motor under the front cover. Usually 90 to 130 V DC, 1.5 to 2.5 horsepower.Its flywheel (about 150 mm), never the small pulley (50 to 70 mm), which gives 30 V and moreWith the flywheel on the tyre, gives about 14 to 18 V at an easy pace. Large, heavy and efficient. Can give dangerous voltages if spun very fast with no battery connected.
B. Scooter or ride-on toy motorOlder chain-drive electric scooters (24 V), children's ride-on cars (12 V or 24 V, often with a gearbox: use the motor, not the gearbox)24 V motor: 40 to 60 mm (a skateboard wheel). 12 V motor: 25 to 35 mm.Common and light. Lower output than a treadmill motor.
C. Car radiator fan motorAny car (scrap or broken), behind the radiator. 12 V, 100 to 300 W.25 to 35 mm, or the bare shaft wrapped with inner tubeMost older cars have one. Only a fan with two wires works: many newer cars have brushless fans with three or more wires and a control box, which do not work here. Remove the fan blade first.
D. Cordless drill (last resort)Older brushed drills onlyA 40 to 60 mm wheel on a bolt in the chuckResults vary a lot: the drill's trigger switch stays in the circuit and may be damaged. Modern brushless drills do not work this way. Test before relying on it.

For technical readers: roller sizing

Aim for about 16 V at the motor while pedalling (14.4 V to charge, plus losses). The motor speed needed is roughly 16 × (rated rpm ÷ rated voltage). For a given pedalling pace on the stand, the roller diameter in millimetres is about 5,300 × road speed (km/h) ÷ motor rpm. A steady easy pace in a middle gear is about 15 to 20 km/h. Example: a 24 V scooter motor rated at 2,750 rpm needs about 1,830 rpm; at 20 km/h, the roller should be about 58 mm. Then fine-tune with the bike's gears. Low-tech Magazine's measured build used a 250 W, 12/24 V permanent-magnet DC motor and found 75 to 78% efficiency above about 6 A; cleaning and oiling the chain roughly doubled output.163

Building it

Timber stand Two A-frames from 100 x 50 mm timber, notched at the top to hold the back axle ends. Screw to a base board 80 x 40 cm. Tyre 3 to 5 cm off the ground. Tie the(Bikes with thru-axles need a trainer.) axle down with cord or straps. Motor mount Motor bolted or strapped to a plank. Plank joined to the base by a door hinge (grey) so it can tilt. Bungee or spring pulls the roller against the tyre: firm enough not to slip when pedalling hard, no firmer. Roller centred on the tyre tread; motor shaft parallel to the wheel axle. Front wheel: rest on a block or a few books so the bike is level.
Figure 14.2. Side view of timber stand and hinged motor mount. A turbo trainer can replace the stand; the motor mount then sits behind or beside the trainer's own roller.
  1. Test the motor. Set a multimeter to DC volts (20 V range). Touch its probes to the two motor wires and spin the shaft fast by hand. Any reading means it will work. No multimeter? Connect a 12 V car bulb across the wires and spin hard: a glow means it works.
  2. Prepare the bike. Clean and oil the chain (this alone can double output). Pump the back tyre hard. Put the bike on the stand and check the wheel spins freely and the bike cannot fall or jump out.
  3. Fit the roller to the motor shaft so it cannot slip. A skateboard wheel can be held between two nuts and washers on a threaded shaft, or glued to a shaft adapter; a sprocket can be wrapped tightly in strips of inner tube and the end tied off.
  4. Build the mount as in Figure 14.2. Line the roller up with the centre of the tyre, with the motor shaft parallel to the wheel's axle.
  5. Find the positive wire. Pedal forwards gently with the roller on the tyre and the multimeter connected. If the reading is positive, the wire on the red probe is the motor's positive (+). If negative, the other wire is. Mark it with red tape.
  6. Check the voltage. Pedal at an easy, steady pace and try different gears. You want about 15 to 18 V with nothing connected. If it is too low, use a harder gear or a bigger roller. If it is much higher than 20 V, use an easier gear or a smaller roller. With an MPPT controller, aim for its start voltage instead (often 18 to 25 V).
  7. Check the part before fitting it. Power supplies hold several three-legged parts that look alike. Set a multimeter to its diode test (borrow one if you can; without one, rely on the test in step 9). Red probe on an outer leg, black probe on the centre leg: about 0.2 to 0.5 V. Probes swapped: no reading. Check both outer legs. If you get a reading only with the red probe on the centre leg, the part is the wrong type: do not use it.
  8. Wire it up exactly as in Figure 14.3, or through a charge controller (best). Put a 1 A fuse in the voltmeter's positive lead. Wire everything except the battery; the next step connects it. With a controller, the battery goes to the controller first, as its instructions say.
  9. Test the diode. With nobody touching the bike, and the wheel free, connect the battery. If the wheel starts to turn by itself, the diode is the wrong way round or faulty: disconnect at once and check the wiring.
  10. First charge. Pedal. The battery voltage should rise slowly, typically to 13 to 14 V while you pedal. Stop if it reaches 14.4 V.
  11. Outputs. Never pedal with phones plugged in unless the battery is firmly clamped: if a clamp comes off, the full motor voltage reaches the phones. Charge phones and power banks from the battery, through a 12 V socket and USB car charger. No socket? A USB car charger can be wired directly: its centre tip is positive (+) and the side springs are negative (-). Join the wires with a terminal block (see "Joining wires without soldering" above) and put a 5 A fuse in the positive wire.
MOTOR(generator) +- DIODEon heat sink outer legs joined= anodes (to motor +) centre leg + metal tab= cathode (to fuse) 15 AFUSE BATTERY12 V +- 12 V socket+ USBcharger 5 A 1 A voltmeter positive (+): mark it with red tape negative (-): blue core Fuses as close to the battery + as possible. Connect the battery last; disconnect it first.
Figure 14.3. Wiring without a charge controller. Current flows from the motor's positive wire into the diode's two outer legs (joined), out of its centre leg and tab, through the 15 A fuse into the battery's positive terminal, and back from the battery's negative terminal to the motor's negative wire (dashed). Outputs and the voltmeter (with its own 1 A fuse) connect across the battery. With a charge controller, the motor goes to the controller's input instead and no diode is needed.

No diode? Switch method

The diode stops the battery from running the motor when you stop pedalling. Without it, the battery would spin the motor and the wheel by itself, draining the battery and risking injury. If you cannot find a diode, put a 12 V switch rated 15 A or more (for example a car accessory switch) in the positive wire, at least 50 cm from the battery. Never connect or disconnect at the battery clamp while pedalling: the spark can ignite the battery's gas. Connect only once you are pedalling, and always disconnect before you stop. This works, but needs discipline; fit a diode as soon as you can.

Charging rules for 12 V batteries

Battery voltage at rest (not pedalling, nothing connected, after an hour)State of charge
12.7 V or moreFull
12.4 V164About three-quarters
12.2 VAbout half: recharge now
12.0 VAbout a quarter
11.8 V or lessFlat: damage likely if left like this

Lithium iron phosphate (LiFePO4) 12 V batteries hold a nearly flat voltage for most of their charge, so voltage is only a rough guide; use the battery's own monitor or app where it has one.165

LiFePO4 voltage at restApproximate state of charge
13.6 VFull
13.2 VAbout 70%
13.0 VAbout 30%: recharge
12.9 VAbout 20%
12.0 V or lessNearly empty

Pedalling rota

Shifts of 20 to 30 minutes at a comfortable pace are best. Ten people pedalling for an hour each produce about 500 Wh a day. After charging losses of about 30%, roughly 350 Wh can be used: about 20 phone charges, or the street's Wi-Fi router for a day plus about 10 phones. Children and older people can take short turns. People who cannot use their legs can turn the pedals by hand (arms produce much less power than legs, so expect a slow charge); this needs the bike fixed upside down and the motor mounted to suit, so build it as a separate set-up.

Warning: batteries and moving parts.
  • Lead-acid batteries give off hydrogen when charging. Charge outdoors or in a well-ventilated space, with no flames, sparks or smoking nearby.
  • A short circuit across a car battery can melt tools, cause burns and start fires. Remove rings and watches. Never let a metal tool touch both terminals. Cover the terminals when not in use.
  • Battery acid burns skin and eyes. Wear glasses. Wash any splash with plenty of water.
  • Keep fingers, hair, loose clothing, children and pets away from the spinning wheel, chain and roller.
  • Treadmill motors can produce over 50 V if spun fast with no battery connected: enough to give a shock. Always keep the battery connected when pedalling hard.

14.6 Bicycle dynamos

Some bikes have a dynamo in the front hub or a bottle dynamo against the tyre, normally used for lights. They produce about 3 W at 6 V, alternating current.167 With a "USB dynamo charger" (a small converter, bought in advance) they can trickle-charge a phone or power bank while you ride or pedal on a stand. It is slow (several hours for a phone), but useful for runners carrying messages between streets.

14.7 Street power station

Rather than every household struggling alone, the Power Lead runs a single charging station:

14.8 Petrol generators and house wiring

Warning. Never plug a generator, inverter or power station into a house socket to power the house wiring (with a "male to male" lead or any other way). This "back-feeds" the wiring and the street's power lines: it can kill line workers and neighbours, and can start fires. Power from a generator reaches the house wiring only through a changeover switch fitted by a registered electrician.168169

14.9 Lithium battery fire safety

Power banks, e-bike batteries, power stations and phones contain lithium batteries. A damaged or badly charged battery can catch fire suddenly and burn fiercely.

Notes

  1. Centre for Sustainable Energy and National Energy Action, "What uses watt?" (typical power of household appliances). https://www.nea.org.uk/wp-content/uploads/2021/07/advice_leaflet_what_uses_watt.pdf (accessed 14 November 2026). Back to text
  2. CPAP.com, "Using CPAP in an RV" (power use of CPAP machines with and without a heated humidifier). https://www.cpap.com/blog/using-cpap-in-rv/ (accessed 14 November 2026). Back to text
  3. Inogen (maker), "Inogen At Home: Energy Savings Calculator" (home concentrator power use, about 100 to 275 W by setting). https://www.inogen.com/products/energy-savings-calculator/ (accessed 14 November 2026). Back to text
  4. Philips, "EverFlo home oxygen system" (average power consumption 350 W). https://www.philips.ca/healthcare/product/HC0044000/everflo-home-oxygen-system (accessed 14 November 2026). Back to text
  5. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  6. European Commission Joint Research Centre, PVGIS (Photovoltaic Geographical Information System), monthly solar output for England. https://re.jrc.ec.europa.eu/pvg_tools/en/ (accessed 14 November 2026). Back to text
  7. Anker SOLIX, "G98 explained: the UK grid connection standard" (inverters must disconnect from the grid when it fails: loss of mains protection). https://www.ankersolix.com/uk/blogs/content/g98-explained-the-uk-grid-connection-standard-for-plug-in-solar (accessed 14 November 2026). Back to text
  8. SMA Solar Technology, press release "SMA expands residential portfolio by adding new Sunny Boy models with secure power supply" (up to 2,000 W of daytime power in a grid outage), via pv magazine. https://www.pv-magazine.com/press-releases/sma-expands-residential-portfolio-by-adding-new-sunny-boy-models-with-secure-power-supply_100025716/ (accessed 14 November 2026). Back to text
  9. GivEnergy, support and installation guides (Emergency Power Supply for inverters). https://givenergy.com/support/ (accessed 14 November 2026). Back to text
  10. US Centers for Disease Control and Prevention, "About Carbon Monoxide Poisoning" (generators more than 20 feet, about 6 metres, from windows, doors and vents; never heat a house with a gas oven). https://www.cdc.gov/carbon-monoxide/about/index.html (accessed 14 November 2026). Back to text
  11. NHS, "Carbon monoxide poisoning". https://www.nhs.uk/conditions/carbon-monoxide-poisoning/ (accessed 14 November 2026). Back to text
  12. Right Fuel Card, "How much fuel is wasted idling?" (industry estimate: a typical car uses about 0.5 to 1 litre an hour at idle). https://rightfuelcard.co.uk/news/how-much-fuel-is-wasted-idling (accessed 14 November 2026). Back to text
  13. CAR magazine, "Hyundai Ioniq 5 vehicle-to-load: does it work?" (up to 3.6 kW). https://www.carmagazine.co.uk/car-news/tech/vehicle-to-load-v2l-does-it-work/ (accessed 14 November 2026). Back to text
  14. Best Chargers, "V2L explained: which UK EVs have vehicle-to-load", 2026. https://www.bestchargers.co.uk/v2l-uk-evs-explained/ (accessed 14 November 2026). Back to text
  15. European Commission Joint Research Centre, PVGIS (Photovoltaic Geographical Information System), monthly solar output for England. https://re.jrc.ec.europa.eu/pvg_tools/en/ (accessed 14 November 2026). Back to text
  16. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  17. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  18. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  19. Low-tech Magazine, "How to Build a Practical Household Bike Generator", March 2022 (measured outputs, generator choice, friction drive, diode and battery charging). https://solar.lowtechmagazine.com/2022/03/how-to-build-a-practical-household-bike-generator/ (accessed 14 November 2026). Back to text
  20. Battery University, "BU-903: How to Measure State-of-charge". https://batteryuniversity.com/article/bu-903-how-to-measure-state-of-charge (accessed 14 November 2026). Back to text
  21. Renogy, "A Comprehensive Guide to LiFePO4 Voltage Chart". https://renogy.com/blog/lifepo4-voltage-chart (accessed 14 November 2026). Back to text
  22. Battery University, "BU-403: Charging Lead Acid". https://batteryuniversity.com/article/bu-403-charging-lead-acid (accessed 14 November 2026). Back to text
  23. Wikipedia, "Hub dynamo" (bicycle dynamos are typically rated 3 W at 6 V). https://en.wikipedia.org/wiki/Hub_dynamo (accessed 14 November 2026). Back to text
  24. SGS Engineering, "Use Your Generator Safely: Generator Safety Guide" (no back-feeding through sockets; changeover switch fitted by an electrician). https://sgs-engineering.com/help-advice/generator-safety-guide (accessed 14 November 2026). Back to text
  25. Ausgrid, "Domestic portable generators: a safety guide". https://www.ausgrid.com.au/-/media/Documents/Safety/Storm-Safety/Generator-Safety.pdf (accessed 14 November 2026). Back to text
  26. National Fire Chiefs Council, "E-bikes and e-scooters fire safety guidance" (do not attempt to extinguish the fire; get out, stay out, call 999). https://www.nationalfirechiefs.org.uk/E-bikes-and-e-scooters-fire-safety-guidance (accessed 14 November 2026). Back to text
  27. Battery University, "BU-410: Charging at High and Low Temperatures" (lithium batteries must not be charged below freezing). https://batteryuniversity.com/article/bu-410-charging-at-high-and-low-temperatures (accessed 14 November 2026). Back to text

Chapter 15Communications in detail

When the phone networks and the internet fail, people feel cut off, rumours spread, and help cannot be called. This chapter sets out a layered plan: simple methods that always work, plus a street network that gives every phone, tablet and laptop a local internet with no outside connection, and a link to the wider world through satellite.

15.1 What works and what does not

MethodIn a long blackout
Mobile calls and dataFail within minutes to hours as mast batteries run out.
Landline phonesDigital landlines fail within minutes to hours, as soon as the router or the street cabinet loses power, unless they have a battery backup.
Home broadbandFails. The home router still works as a local Wi-Fi network if it has power.
FM radio receiversWork, as long as broadcasters stay on air. Many transmitter sites have backup power, but it does not last for ever.172
Face to face, notice boards, runners, whistlesAlways work.
Walkie-talkies (PMR446)Work. Licence-free types differ by country (in the UK, PMR446)173; in town, expect a few hundred metres to about 1 km.
Bluetooth phone-to-phone apps (BitChat)Work between nearby phones, if installed before the outage.
A local Wi-Fi network with a local serverWorks for every device with a web browser, with no app needed.
LoRa radio mesh (Meshtastic, MeshCore)Works over kilometres for short text messages, with small radio devices.
Starlink satellite internetWorks anywhere with power and a view of the sky; connects to the outside world.
Satellite SOS on newer phonesiPhone 14 and later can text emergency services by satellite when there is no signal, in the UK and the other countries Apple lists.174

15.2 Layered plan

8 Outside worldStarlink dish (shared), satellite SOS, FM news radio 7 Between neighbourhoodsLoRa mesh radios (kilometres), licensed radio amateurs 6 Between streetsOutdoor Wi-Fi links, LoRa radios, runners on bikes 5 Street networkLocal Wi-Fi + hub: community app, library, guide, notices 4 Phone to phoneBitChat over Bluetooth (installed in advance) 3 Team radiosLicence-free walkie-talkies 2 SignalsWhistles (Chapter 12), torches, a flag at the meeting point 1 AlwaysFace to face, meetings, notice board, written messages, runners
Figure 15.1. Communication layers. Each layer is a backup for the one above it. Layer 1 always works; build upwards from it.

15.3 Layers 1 to 3: basics

Written messages

Every message that matters is written down, timed and signed, using this simple form (Message Pad, form 12):

FROM (person, street) · TO · TIME · WHERE · WHAT has happened · NEED (what you are asking for) · CONFIRMED? (seen yourself, or heard from someone)

Walkie-talkies

PMR446 radios are licence-free in the UK; the rules for licence-free radios differ by country, so check yours before you buy. Agree channels in advance and write them on each radio: for example, channel 1 for street calls, channel 2 for the night watch, channel 3 for the water and power teams. "Privacy codes" only filter what you hear; anyone can listen. Keep messages short, say who you are calling and who you are ("Water team, this is Street Base"), and never share private information over the radio.

Licensed radio amateurs

Ask in the census whether anyone holds an amateur radio licence. Many countries have a volunteer network of licensed amateurs who support the emergency services in a crisis (in the UK, RAYNET-UK; in the United States, the Amateur Radio Emergency Service, ARES175); local members can relay messages over long distances.176

15.4 Layer 4: phone to phone with BitChat

BitChat is a free, open-source app that sends text messages directly between phones using Bluetooth, with no internet and no phone network. Each phone relays messages for others, up to 7 hops, so a message can travel along a street from phone to phone.177 It works between iPhone and Android phones, and on Mac computers.

15.5 Layer 5: street network (our local internet)

The street network is a Wi-Fi network covering the street, powered by batteries, with a small computer (the "hub") serving web pages. Anyone who joins the Wi-Fi can open the hub in their phone's normal web browser. No app is needed, so it works on every iPhone, Android phone, tablet and laptop, including phones that were not prepared.

The hub provides:

THE STREET HUBlaptop+ router REPEATERon battery STARLINK optional link: hub uses Starlink to reach the outside world LoRa radio (roof or upstairs window) outdoor Wi-Fi linkto the next street Dotted circles: Wi-Fi coverage, about 30 to 50 m from each box, less through thick walls.
Figure 15.2. Typical street network: one hub, one or more repeaters to cover the length of the street, an optional Starlink link, an outdoor Wi-Fi link to the next street and a LoRa radio for longer distances. Everything runs from 12 V batteries.

How to join (for everyone)

  1. Find the street network poster (on the notice board and lamp posts). It has two square QR codes.
  2. Open your phone camera and point it at the first code. Tap "Join network". (Or go to Wi-Fi settings and choose the network printed on the poster, then type the password.)
  3. Your phone may say "No internet connection". That is expected. Stay connected. On Android, tap "Keep Wi-Fi connection" or "Stay connected" if asked, and turn off "Switch to mobile data" if your phone offers it.
  4. Point the camera at the second code to open the hub in your browser. Or type the address printed on the poster.
  5. At the welcome desk, install the street's security certificate once (two minutes, steps on the start page). It keeps the hub working on your phone for the whole crisis.
  6. Register on the community app. An administrator confirms your account at the welcome desk once a role holder has vouched for you.

The technical framework (how the hub is built, powered, secured and kept running) is Chapter 16.

15.6 Layers 6 and 7: between streets and neighbourhoods

15.7 Layer 8: outside world and Starlink

A Starlink dish connects to satellites and gives full internet access wherever it has power and a clear view of the sky. Starlink satellites pass data between each other by laser, so a dish can reach the internet through ground stations in other countries; it does not depend on a ground station near you.186 One Starlink dish, shared through the street network, can connect the whole street to the outside world: news, family, emergency services, information.

Finding Starlink owners: do this now

Standard (about 60 x 40 cm) Mini (about 30 x 25 cm) Older round (about 60 cm) Not Starlink:TV dish (dish + arm)
Figure 15.3. Starlink dishes are flat with no arm sticking out in front. TV satellite dishes are curved with an arm.

Powering and sharing Starlink

Satellite on ordinary phones

15.8 Why not build our own Bluetooth app?

Is there a Bluetooth app that works on every device, including iPhones, without the internet? If not, should a street build one?

Decision: do not build a Bluetooth app. Install BitChat on every phone now, and build the street network on Wi-Fi with a web-based hub, which works on every current phone, tablet and laptop. The technical framework (section 16.2) gives the full reasoning and sources.

15.9 Rumours and information

Notes

  1. Arqiva, "Television, Resilience and National Security" (many transmitter sites have backup power arrangements). https://www.arqiva.com/news/television-resilience-and-national-security (accessed 14 November 2026). Back to text
  2. Ofcom, "Licence-exempt devices" (PMR446 walkie-talkies may be used without a licence). https://www.ofcom.org.uk/spectrum/radio-equipment/licence-exempt-devices (accessed 14 November 2026). Back to text
  3. ISPreview, "Apple enables Emergency SOS via satellite in UK on iPhone 14", December 2022. https://www.ispreview.co.uk/index.php/2022/12/apple-enables-emergency-sos-via-satellite-in-uk-on-iphone-14.html (accessed 14 November 2026). Back to text
  4. American Radio Relay League, "ARES: Amateur Radio Emergency Service". https://www.arrl.org/ares (accessed 16 November 2026). Back to text
  5. RAYNET-UK (Radio Amateurs' Emergency Network). https://www.raynet-uk.net/ (accessed 14 November 2026). Back to text
  6. permissionlesstech, "bitchat" (source code and documentation). https://github.com/permissionlesstech/bitchat (accessed 14 November 2026). Back to text
  7. Bluetooth SIG, "Understanding Bluetooth range" (range depends on the radio, the antenna and obstacles). https://www.bluetooth.com/learn-about-bluetooth/key-attributes/range/ (accessed 14 November 2026). Back to text
  8. The Register, "Jack Dorsey floats specs for decentralized messaging app that uses Bluetooth", July 2025. https://www.theregister.com/2025/07/08/jack_dorsey_debuts_bitchat/ (accessed 14 November 2026). Back to text
  9. Meshtastic, "Introduction" (documentation). https://meshtastic.org/docs/overview/ (accessed 14 November 2026). Back to text
  10. MeshCore, project repository and documentation, GitHub. https://github.com/meshcore-dev/MeshCore (accessed 14 November 2026). Back to text
  11. Ofcom, "IR 2030: UK Interface Requirements for Licence Exempt Short Range Devices". https://www.ofcom.org.uk/__data/assets/pdf_file/0028/84970/ir-2030.pdf (accessed 14 November 2026). Back to text
  12. Meshtastic, "LoRa Configuration" (region settings: EU_868, US 902 to 928 MHz, ANZ 915 to 928 MHz; set the region for your country). https://meshtastic.org/docs/configuration/radio/lora/ (accessed 16 November 2026). Back to text
  13. Meshtastic, "Introduction" (documentation). https://meshtastic.org/docs/overview/ (accessed 14 November 2026). Back to text
  14. MeshCore, project repository and documentation, GitHub. https://github.com/meshcore-dev/MeshCore (accessed 14 November 2026). Back to text
  15. Starlink, "Technology" (laser links between satellites). https://www.starlink.com/technology (accessed 14 November 2026). Back to text
  16. Starlink, "Starlink kit" specifications (Standard kit: average power 75 to 100 W). https://www.starlink.com/kit (accessed 14 November 2026). Back to text
  17. DishyTech, "Starlink Dish Placement: Which Direction Should It Face?" (dishes in the northern hemisphere tilt towards the north). https://www.dishytech.com/starlink-dish-placement-which-way-should-it-face/ (accessed 14 November 2026). Back to text
  18. WiGLE, the Wireless Geographic Logging Engine (community map of Wi-Fi networks). https://wigle.net/ (accessed 14 November 2026). Back to text
  19. Krebs on Security, "Why Your Wi-Fi Router Doubles as an Apple AirTag" (Starlink router location data and BSSID randomisation), May 2024. https://krebsonsecurity.com/2024/05/why-your-wi-fi-router-doubles-as-an-apple-airtag/ (accessed 14 November 2026). Back to text
  20. Starlink, "Availability map" (where the service can be ordered). https://www.starlink.com/map (accessed 14 November 2026). Back to text
  21. Starlink, "Specifications: Starlink Mini" (average power 25 to 40 W; USB PD 100 W). https://www.starlink.com/specifications?spec=5 (accessed 14 November 2026). Back to text
  22. Starlink, "Starlink kit" specifications (Standard kit: average power 75 to 100 W). https://www.starlink.com/kit (accessed 14 November 2026). Back to text
  23. ISPreview, "Apple enables Emergency SOS via satellite in UK on iPhone 14", December 2022. https://www.ispreview.co.uk/index.php/2022/12/apple-enables-emergency-sos-via-satellite-in-uk-on-iphone-14.html (accessed 14 November 2026). Back to text
  24. Virgin Media O2, "Virgin Media O2 becomes the first UK mobile network to switch on direct-to-device satellite connectivity with the launch of O2 Satellite", 26 February 2026. https://news.virginmediao2.co.uk/virgin-media-o2-becomes-the-first-uk-mobile-network-to-switch-on-direct-to-device-satellite-connectivity-with-the-launch-of-o2-satellite/ (accessed 14 November 2026). Back to text
  25. Apple Support, "About alternative app distribution" (available in Brazil, Japan and the countries or regions of the European Union). https://support.apple.com/en-us/118110 (accessed 16 November 2026). Back to text
  26. Apple, "Create an ad hoc provisioning profile" and "Distribute to registered devices", Xcode Help. https://help.apple.com/xcode/mac/current/en.lproj/dev4335bfd3d.html (accessed 14 November 2026). Back to text
  27. The Register, "Apple, Google agree to loosen grip on UK app stores", February 2026. https://www.theregister.com/2026/02/10/apple_google_uk_app_stores/ (accessed 14 November 2026). Back to text
  28. Briar Project, "Briar 1.4 released" (share the app offline), November 2021. https://briarproject.org/news/2021-briar-1.4-released/ (accessed 14 November 2026). Back to text
  29. Bluetooth SIG, "Understanding Bluetooth range" (range depends on the radio, the antenna and obstacles). https://www.bluetooth.com/learn-about-bluetooth/key-attributes/range/ (accessed 14 November 2026). Back to text

Chapter 16Street network and community hub

For the Communications and Network Lead and technical helpers. Builds on Chapter 15. Configuration files are in the technical/street-hub folder of this pack.

In this chapter, the hub keeper is the person who prepares and runs the hub: the Communications and Network Lead, or a helper they appoint.

What this chapter decides

QuestionDecision
Bluetooth mesh app: use an existing one or build one?Use BitChat (installed in advance). Do not build one: a homemade app cannot reach unprepared iPhones either (section 16.2).
How do unprepared devices, especially iPhones, join the local internet?Through the web browser on a battery-powered Wi-Fi network. No app needed.
How is the community app served offline?A self-hosted, open-source, browser-based app running in Docker on the hub computer, behind Caddy, with its mail going to the hub's own mail server (Chapter 17), or to Mailpit until that is set up (section 16.8).
Address and HTTPSThe hub's own address under a domain the street controls (the examples use hub.example.org), with a real public certificate obtained in advance (zero setup on every device), then the street's own certificate authority before the public certificate expires. HTTPS protects passwords on a shared Wi-Fi network (section 16.6).
One hub per street, or one for the neighbourhood?One hub for the whole neighbourhood, with one community app instance, from the start. Other streets join it over Wi-Fi links (section 16.5.6).
PowerEverything runs on 12 V DC from one 100 Ah lithium iron phosphate battery (a day and a half to two days), recharged by car, electric car, solar or pedal (section 16.4).

16.1 Requirements and constraints

16.1.1 What your network must do

  1. Let any phone, tablet or laptop near the street reach shared services with no internet, no mobile network and no app installation.
  2. Serve a community app for registration, messaging, notices, project planning and coordination, for a street growing into a neighbourhood (tens to a few hundred people).
  3. Serve the offline library, this guide, Android app files and, when power allows, an AI assistant.
  4. Run for weeks on batteries charged from improvised sources.
  5. Survive the loss of any single box (a spare plan for each).
  6. When a Starlink dish is available, share an internet link fairly.

16.1.2 Constraints to plan for

ConstraintConsequence
Some browser features that web apps use (encryption in the browser, offline storage) work only on HTTPS pages (or localhost).201Plan for HTTPS with a certificate every device trusts. Plain HTTP on the local network may break sign-in and messaging.
Your DNS provider must offer an API for automatic DNS validation.Certificates can then be obtained in advance without the hub being reachable from the internet.
Apps that send email (sign-up codes, notices) cannot reach a mail server with no internet.Send it to the hub's own mail server (Chapter 17). Until that is set up, capture it with Mailpit and hand codes over in person.
The hub computer has limited memory and disk space.Keep large data on an external drive; memory limits for AI are in Chapter 21.

16.2 Bluetooth and iPhone question

16.2.1 What exists

AppiPhoneAndroidDesktopTransportAssessment
BitChat (permissionlesstech)App Store, iOS 16+Google Play com.bitchat.droid; GitHub APK (v2.0.1 in 2026)macOS (App Store)Bluetooth LE mesh, up to 7 hops; Nostr over the internetBest current choice. Open source, public domain, actively maintained, iPhone and Android interoperate. Bluetooth range and iOS background limits apply.
BriarNoYes (Play, F-Droid, APK)Briar Desktop (beta)Bluetooth, Wi-Fi, TorMature and secure. Android only. "Share this app offline" serves its own APK over a temporary hotspot.
BridgefyYesYesNoBluetooth meshClosed source; past security criticism; older versions needed internet once to activate.
BertyBetaBetaPartialBLE, local networkOpen source, slow development.
Meshtastic, MeshCoreAppAppWebLoRa radio hardware (868 MHz in the UK and Europe; other bands elsewhere)Excellent for long-range text between streets; needs a radio per user or per street.

16.2.2 Getting native apps onto iPhones with no internet

16.2.3 Decision

A homemade Bluetooth app would face the same limit: no unprepared iPhone could install it. It would also take months to build, test and get through App Review, and would add nothing BitChat does not already do. And Bluetooth does not suit a "local internet": a range of a few tens of metres between phones, little bandwidth, and phones throttle it in the background.

16.3 Architecture

Shape of the hub: devices with a web browser join the Wi-Fi; the router answers requests for the hub's web address with the hub computer's IP address; on the hub, Caddy terminates HTTPS and passes requests to the community app, the Kiwix library, the start page and, when power allows, the AI server. Only Caddy (and the mail server, once street email is set up) is reachable from the network. Everything large (images archive, library, certificates, backups, models) sits on an external drive.

Any deviceweb browser onlyhttps://hub.example.org Wi-Fi router (OpenWrt)DHCP and local DNS:hub address to 192.168.8.10repeaters, outdoor links Starlink (optional)router joins its Wi-Fias internet uplink;hub stays local Hub laptop, 192.168.8.10, Docker, powered from 12 V USB-C hub-proxy (Caddy)HTTPS 443, start page 80 community app + database library (Kiwix) AI (llama-server)
Figure 16.1. Hub. Caddy is the only service reachable from the network (and the mail server, once street email is set up). Any mail from the app goes to a mail service on the hub computer (Chapter 17).

16.4 Hardware and power

16.4.1 Bill of materials

ItemStatusWhy this oneRough cost
Hub computer: a laptop with 8 GB or more (any recent low-power laptop)Have or buyLow power (8 to 15 W as a server), own battery as a built-in UPS. Use a dedicated laptop, or at least a separate user account with no work or personal files, saved passwords or access tokens on it, because two helpers will know its password; keep the hub data on a dedicated drive.varies
External SSD, 1 to 2 TB, encryptedBuyHolds everything large: keep it physically safe.60 to 100 GBP
Main router: an OpenWrt-based travel router powered by USB-C 5 V, for example GL.iNet GL-MT3000 (Beryl AX)BuyRuns from a power bank or 12 V USB; full control of DHCP and DNS (needed for the hub address override); repeater mode for Starlink; per-client limits; AP isolation.70 to 90 GBP
Spare router of the same modelBuyA configured spare in a box: swap in two minutes.70 to 90 GBP
Repeaters or access points (same model or any OpenWrt router): one per 30 to 50 m of street. This is a planning figure; the coverage walk (test 13 in section 16.12) gives the real spacing.Buy 1 to 3Coverage along the street. Wired back to the hub where a cable can run between houses; otherwise wireless repeater.40 to 90 GBP each
Outdoor Wi-Fi bridge pair, 5 GHz (for example TP-Link CPE510 or Ubiquiti NanoStation)Buy 1 pair per neighbouring streetLinks streets hundreds of metres apart if they can see each other.80 to 120 GBP a pair
12 V 100 Ah lithium iron phosphate (LiFePO4) battery with built-in BMSBuyAbout 1.2 kWh usable, thousands of cycles, safe chemistry, no gassing.200 to 300 GBP
LiFePO4 charger (12 V, mains) and a DC-DC charger (never jump leads with a lithium battery) for car chargingBuyRecharge from an electric car's V2L socket, a car, or a power station.40 to 120 GBP
12 V USB-C PD car charger, 65 W or more, two portsBuy 2Runs the hub laptop (needs 30 to 60 W) and the router from the 12 V battery with no inverter.15 to 30 GBP each
Powered USB-C hub with an Ethernet port and power pass-through (100 W)BuyChoose a hub with enough ports for power, Ethernet and the drive. Choose one tested with your laptop.30 to 60 GBP
12 V fuse block, fuses, 6 mm² cable from battery to fuse block, 1.5 to 2.5 mm² for branches, ring terminals, a DC watt meterBuySafe wiring and a view of consumption.30 to 50 GBP
12 V to 24 V step-up converter and passive PoE injectorBuy if using outdoor bridgesOutdoor bridges are powered by 24 V passive PoE.15 to 25 GBP
Folding solar panel 100 to 200 W with a LiFePO4-capable MPPT controllerBuyUseful charging in the sunnier months (in the UK, March to October).150 to 300 GBP
LoRa radios (Meshtastic or MeshCore) for your region's band (868 MHz in the UK and Europe), two or moreBuyText link between streets and neighbourhoods, independent of Wi-Fi.25 to 60 GBP each
Small managed (802.1Q VLAN) Ethernet switch, 5 or 8 ports, powered from 5 V USB through a barrel cable (for example TP-Link TL-SG105E; check its input voltage)BuyThe router has only two Ethernet ports: the switch adds ports for the hub, wired access points and, on its own VLAN, the link to another neighbourhood. An unmanaged switch cannot keep the link separate.25 to 40 GBP
Ethernet cables (20 to 50 m outdoor-rated), USB-C cables, cable ties, tapeBuyWired links between houses are faster and more reliable than repeaters.30 GBP
Laminated QR posters (Wi-Fi join code and hub address)MakeJoin without typing. QR text for Wi-Fi: WIFI:T:WPA;S:<network>;P:<password>;;10 GBP

16.4.2 Power budget

LoadAveragePer day
Hub computer (Docker running, screen off)8 to 15 W0.2 to 0.36 kWh
Main router5 to 8 W0.12 to 0.19 kWh
One repeater5 W0.12 kWh
One outdoor bridge4 to 6 W0.1 to 0.14 kWh
LoRa radiounder 1 W0.02 kWh
Base total (hub laptop, router, repeater, one bridge, LoRa)about 25 to 35 Wabout 0.6 to 0.85 kWh
Starlink Mini, if powered by the hub battery25 to 40 Wrun in set hours only
AI assistant sessions (hub laptop under load)20 to 30 W extraby session only

A 100 Ah LiFePO4 battery (about 1.2 kWh usable) runs the base network for about a day and a half to two days. Recharging it fully takes roughly 25 to 35 hours of pedalling (after losses), 4 to 8 hours on a 10 to 20 A charger from an electric car's V2L socket or a car's inverter, or a 200 W panel for about 2 days in summer and about 10 days in an English December. The plan: recharge daily from whichever source is available, and treat the laptop's own battery (typically 50 to 70 Wh) as a 3 to 5 hour UPS.

16.4.3 Wiring

Each charging source connects through its own fuse at the battery or the fuse block, sized as its maker states.

LiFePO4 12 V (+) ── 30 A main fuse (within 15 cm of the battery, 6 mm² cable) ── fuse block ─┬─ 10 A ── USB-C PD charger #1 ── laptop (USB-C, 60 W)
                                                  ├─ 10 A ── USB-C PD charger #2 ── main router (USB-C 5 V 3 A)
                                                  ├─ 5 A ─── 12→24 V boost ── PoE injector ── outdoor bridge
                                                  └─ 5 A ─── spare
LiFePO4 12 V (−) ── negative bus bar ── all returns
Charging into the battery: LiFePO4 charger (from V2L or inverter), a DC-DC charger from a car with the
engine running, an MPPT solar controller, or the pedal generator ONLY through a charge controller rated
for the motor's highest voltage and set to its lithium setting (the battery's protection board can
disconnect, and the motor's voltage would then reach the laptop and router). Never charge LiFePO4 below 0 °C.

16.4.4 Placement

16.5 Network design

16.5.1 Wi-Fi

16.5.2 Addresses

ItemSetting
Main router LAN address192.168.8.1, netmask 255.255.252.0 (a /22: room for about 1,000 devices as the neighbourhood joins)
Hub computer192.168.8.10, connected to the main router by Ethernet cable (needed: with AP isolation on, Wi-Fi clients cannot reach a hub that is itself on Wi-Fi), with a DHCP reservation for its Ethernet MAC address (through the USB-C hub's Ethernet port; reserve the address of that port)
Infrastructure (repeaters, bridges)192.168.8.2 to 192.168.8.99, fixed
DHCP pool192.168.8.100 to 192.168.11.250, lease 12 hours
DHCP serverThe main router only. All other routers in "access point" mode with DHCP off.

16.5.3 Local DNS

On the main router (OpenWrt: Advanced settings, LuCI, Network, DHCP and DNS, General, "Addresses"), add one line:

/hub.example.org/192.168.8.10

This answers hub.example.org (replace it with the hub address) and every address under it205 (library, ai, mail) with the hub's address. Also add /hub.lan/192.168.8.10. Test from a phone: https://hub.example.org must open with a padlock and no warning.

At your DNS provider, also publish hub.example.org and *.hub.example.org as A records to 192.168.8.10, DNS only (not proxied, where the provider offers proxying). It is harmless (a private address) and makes the addresses work for devices still using outside DNS, for example when the router is connected through Starlink.

Device settings that break local addresses (printed on the start page): Android "Private DNS" set to a specific provider (set to Automatic or Off); iPhone "Limit IP Address Tracking" and iCloud Private Relay (turn off for this network); browsers with "secure DNS" in strict mode (set to automatic).

16.5.4 Coverage along your street

  1. Start with the main router at the hub. Walk the street with a phone and note where the signal falls below two bars.
  2. Where an Ethernet cable can run between houses (over a fence, along a wall), wire an access point there. Wired access points do not halve the speed.
  3. Elsewhere, set a router as a wireless extender in a mode that keeps one network (on GL.iNet routers "Extender" or WDS mode, or an 802.11s mesh on OpenWrt; not "Repeater" mode, which makes a separate network with its own DHCP). Give each access point a fixed address from 192.168.8.2 to 192.168.8.99 and turn its DHCP off. Each wireless hop roughly halves throughput; for text messaging and web pages this is acceptable. Keep it to two hops.
  4. Plan about 30 to 50 active phones per access point for good performance.

16.5.5 Optional captive page

OpenWrt can show a welcome page automatically when a phone joins (a "captive portal", for example with the openNDS package). It is a convenience only: the iOS captive sheet is a limited browser that cannot run a full web app properly. The posters and the start page are enough. If added later, the captive page should only show a button that opens the hub address in the real browser.

16.5.6 Neighbourhood: one hub, many streets

Most self-hosted apps cannot merge two instances later. So from the first day, run one instance for the whole neighbourhood on the best-powered hub. When a neighbouring street joins:

  1. Mount an outdoor bridge pair: one unit at our street ("access point" mode), one at theirs ("client/station" mode with WDS bridging, so it is transparent).
  2. Their routers run as access points with DHCP off and the same Wi-Fi network. Their devices get addresses from our main router and reach the same hub.
  3. If line of sight is impossible, they use runners and LoRa until a relay point can be found (a tall building that sees both).

Linking two neighbourhoods. Each neighbourhood keeps its own hub, its own address range (for example 192.168.8.0/22 for the first, 192.168.12.0/22 for the second), its own hub address and its own certificate authority. Join them with a routed link, never a bridged one, so that two DHCP servers never meet:

  1. If Starlink joins by Wi-Fi (section 16.5.7), remove the WAN port's device from the wan and wan6 interfaces, plug the outdoor bridge into it and give it a new interface (not wan). If the WAN port carries a cable, use the managed switch: port 1 to the router's LAN port (VLAN 1 untagged, VLAN 250 tagged, PVID 1); port 2 to the hub (VLAN 1 untagged, PVID 1); port 3 to the outdoor bridge (VLAN 250 untagged, PVID 250, not a member of VLAN 1); ports 4 and 5 to wired access points (VLAN 1 untagged, PVID 1, not members of VLAN 250). On the router, add a VLAN (802.1q) device with ID 250 on the LAN port's device, as listed under Network, Interfaces, Devices, and a new interface on it.
  2. Give the link its own small network (for example 10.250.0.0/30: 10.250.0.1 at one end, 10.250.0.2 at the other), with no gateway on the link interface.
  3. On each router, add a fixed route to the other neighbourhood's range through the other end of the link.
  4. Make a new firewall zone for the link, with masquerading (NAT) off, input and forward set to reject, and one traffic rule from the link zone to the hub address (192.168.8.10, TCP 25, 80 and 443), so phones in one neighbourhood are not exposed to the other. Allow forwarding from lan to the link zone, so your phones and hub can reach the other hub. Phones reach the other hub only by its IP address (its start page, plain HTTP); its web pages need its own DNS line and CA. Do not use the wan zone, which must keep masquerading on for Starlink.

Give each neighbourhood its own web address (for example a different subdomain), because each router's local DNS line and each certificate authority cover only their own. The second neighbourhood makes its own certificate authority for its own address range: ./make-local-ca.sh <CA folder> <staging folder> <its hub address> 192.168.12.10 192.168.12.0/255.255.252.0. It also gets its own phase 1 public certificate for its address (section 16.6.2), its own settings file (HUB_HOST and HUB_IP), and its own copy of the start page with its addresses. Test it in the rehearsal (test 18). Email passes between the two hubs (Chapter 17); each community app stays separate.

At several hundred users, move the hub to a more powerful machine if one is available (the move is: stop, back up, restore on the new machine, change the DNS line).

16.5.7 Sharing Starlink links

16.6 Addresses and HTTPS

16.6.1 Why HTTPS matters here

Use HTTPS with a certificate every device trusts: street webmail (and the AI front end, if it has accounts) takes passwords on a Wi-Fi network whose password everyone knows, and many web apps need HTTPS. The hub therefore needs a certificate for its address that every device trusts, for as long as the crisis lasts. The examples below use hub.example.org: replace it with an address under a domain you control.

16.6.2 Phase 1: public certificate (zero setup for users)

Obtain now, while the internet works, a certificate for hub.example.org and *.hub.example.org by DNS validation through your DNS provider's API. Every phone already trusts it.

  1. At your DNS provider, create an API token that can edit DNS records for the hub's domain only. Store it in a password manager. (Cloudflare is one common choice; deSEC, Gandi and many others work the same way.)
  2. Use the goacme/lego Docker image206 (pulled and pinned now):
    docker run --rm \
      -e CLOUDFLARE_DNS_API_TOKEN="$TOKEN" \
      -v "/path/to/hub-data/lego:/.lego" \
      goacme/lego:<pinned> --accept-tos --email <your address> \
      --dns cloudflare -d hub.example.org -d '*.hub.example.org' run
    This example is for Cloudflare. Other providers use their own --dns setting and token variable (lego documentation). The files appear as certificates/hub.example.org.crt (full chain) and certificates/hub.example.org.key. Copy them into CERT_DIR as fullchain.pem and privkey.pem.
  3. Renew every two weeks while the internet works (same command with renew --days 75). After each renewal, copy the new .crt and .key into CERT_DIR as fullchain.pem and privkey.pem and run docker restart hub-proxy hub-mailserver (leave out hub-mailserver if street email is not set up): both read the certificate only when they start. Let's Encrypt certificates last 90 days, so this keeps at least about 60 days of validity (certificate lifetimes will shorten from 2026 to 2029, so check this margin each year207) on the day the internet goes.
  4. For a longer runway, optionally buy a commercial DV certificate for the same addresses and re-issue it every month. Since 15 March 2026 public certificates may last up to 200 days (100 days from 15 March 2027, 47 days from 2029, under CA/Browser Forum ballot SC-081).208 A monthly re-issue keeps at least about 170 days in hand (about 70 days once certificate lifetimes shorten from March 2027).

Note: these addresses appear in public Certificate Transparency logs. That reveals only that the hub address exists.

16.6.3 Phase 2: street's own certificate authority

When the public certificate nears expiry, the hub switches to a certificate signed by the street's own certificate authority (CA). Each device must trust that CA once. A device without the CA shows a certificate warning after the switch (a hard error if the domain uses HSTS), so phase 2 is rolled out before phase 1 expires.

  1. Now: run technical/street-hub/make-local-ca.sh to create the CA (10 years) and a hub certificate (valid 397 days, within Apple's 825-day limit for user-installed CAs,209 with serverAuth and the addresses hub.example.org, *.hub.example.org, hub.lan and the hub IP) in a separate staging folder such as certs-local. Never use the live certificate folder: the script refuses a folder that holds the public certificate or the folder given as CERT_DIR. The CA is limited by built-in constraints to the hub's own addresses and the street network's addresses, so even a stolen CA key could not be used to impersonate a bank or any other website. The script writes the CA's private key to a separate folder: keep it on a USB stick that is plugged in only while the script runs, with a second copy sealed and held by another person; it never stays on the hub. The script has been tested: the certificate verifies against the CA and carries the right addresses, key usage and constraints.
  2. Copy street-ca.crt into the hub's info folder. Phones download it from http://192.168.8.10/street-ca.crt (plain HTTP by IP address works before the CA is installed).
  3. From the first day, and at the street meeting held before any crisis: the welcome desk installs the CA on every device during registration (two minutes, steps on the start page for iPhone, Android, Windows and Mac). Keep a tally. The poster's second QR code points to http://192.168.8.10/ (the start page by IP address), so that a phone without the CA can always reach the instructions.
  4. Switch 14 days before the public certificate expires, not earlier. Until then, keep installing the CA at registration, so newcomers and visitors are never locked out. On switch day, check the local certificate first: openssl x509 -in <staging folder>/fullchain.pem -noout -enddate. If fewer than 60 days remain, plug in the CA USB stick and re-issue it with make-local-ca.sh. Then copy the local fullchain.pem and privkey.pem from the staging folder into CERT_DIR and run docker restart hub-proxy hub-mailserver (leave out hub-mailserver if street email is not set up). Post a notice the day before.
  5. Re-issue the hub certificate yearly with the same script into the staging folder (the CA is kept, devices need nothing new), then copy it into CERT_DIR and restart both services as above.

Firefox uses its own certificate store; on Firefox users should use the system browser for street pages, or import the CA in Firefox settings.

16.7 What to prepare now, while internet access works

16.7.1 Software inventory

ItemHowWhere it goesSize
Your community app's container images and its database imagePull or build, then pin exact versionsDocker, then one archive on the external drive0.5 to 2 GB
Mailpit, kiwix-serve, Caddy imagesdocker pull, then record digests in hub.envSameabout 0.4 GB together
goacme/lego imagedocker pullDocker only (needed while online)small
Docker installer for the hub computer's system (macOS, Windows or Linux)DownloadExternal driveabout 0.6 GB
Offline library (.zim files, Chapter 21)Download from download.kiwix.orgExternal drive, ZIM_DIRabout 50 to 300 GB depending on choice
Android APKs: BitChat (GitHub release), Briar, Organic Maps, Kiwix, Meshtastic or MeshCore, F-DroidDownload from each project's official site; record SHA-256 hashesExternal drive, then info/apps/about 0.5 GB
The guide and formsCopy Civilised Blackout.html, the printables folder and the assets folder into info/ (the guide needs assets for its fonts and logo)Hubsmall
AI runtime and model filesSee Chapter 21External drive5 to 100 GB
Router firmware files and the router maker's manual (PDF)DownloadExternal drivesmall
Documentation: Caddy, Docker, OpenWrt and your app's database (DevDocs ZIMs)DownloadLibrarysmall
WireGuard client for the hub's system (install it now; keep the installers on the external drive)DownloadHub, and the external drivesmall

Then run technical/street-hub/save-images.sh to put every image into one archive on the external drive, and test a restore with docker load on the archive. The script gives each pinned image a local tag, so that a restored hub never tries to download anything. Images pulled on an ARM computer (for example Apple silicon) run only on ARM computers: to be able to restore on an ordinary Intel or AMD computer as well, save a second set built for linux/amd64, as the script's notes explain. Pull the small alpine image too: the backup script needs it.

16.7.2 Disk space

Keep the image archive, library, certificates, backups and models on the external drive, not on the hub computer's internal disk. If Docker's own data grows large, move it to the external drive in Docker's settings (Docker Desktop: Settings, Resources; Linux: data-root in /etc/docker/daemon.json); the drive must then stay connected whenever Docker runs.

16.8 Community app on your hub

The hub can serve any self-hosted web app. Choose one now and rehearse with it. What to look for:

Common kinds of open-source tools that fit include team chat servers with a web client, forum software and simple task boards. Whatever you choose: run it behind Caddy at the hub address, keep its data volumes on the external drive, back it up nightly, and include it in the rehearsal (section 16.12).

How the street uses it: one group for the street (later the neighbourhood) with a channel per working group; notices marked CONFIRMED or UNCONFIRMED; task lists for projects (the water station, the generator, the warm room). Paper remains the record of truth for votes; the app carries copies.

16.8.1 First start (runbook)

  1. External drive connected. Docker running with enough memory for your app (give Docker about half of the computer's memory).
  2. If this computer has never had the images: docker load -i /path/to/hub-data/hub-images.tar.
  3. In the street-hub folder, with hub.env filled in, start everything with the exact command written at the top of docker-compose.yml (once street email is set up, add -f mail/docker-compose.mail.yml before up).
  4. Wait until docker ps shows every container running and the app's logs show it is ready.
  5. From a phone on the street Wi-Fi: open the hub address. Padlock, no warning, the app's front page.
  6. Create the first administrator account, following the app's documentation. Record the act in the Decisions Book.
  7. Copy the guide, printables and assets into info/; check the start page by IP address (http://192.168.8.10/) and by web address (https://hub.example.org/info/).
  8. Check the library at the library address.
  9. Run the app's backup once by hand and check the files appear on the external drive.

16.8.2 Street registration

16.8.3 What will not work offline

16.9 Running it day to day

16.10 Security and privacy

16.11 Failure modes and recovery

FailureRecovery
Hub computer diesAny computer with Docker (macOS, Windows or Linux): install Docker from the external drive, docker load the image archive, then follow "Restore, step by step" below. In short: copy the street-hub folder and hub.env, start, restore the newest backup by the app's documented restore, give it address 192.168.8.10. Target: under 2 hours.
External drive lost or damagedRebuild from the newest weekly kit copy (from the other house) and the nightly second copy: install Docker from the kit, docker load the image archive, restore the newest data. At most a week of library or model changes and a day of data are lost.
Main router diesSwap in the configured spare.
Battery flatThe hub laptop runs 3 to 5 hours on its own battery; the router can run from a power bank. Recharge from any source (Chapter 14).
Public certificate expires before phase 2 is completeSwitch to the local certificate at once; devices without the CA install it from http://192.168.8.10/.
Database corruptionRestore last night's backup; at most a day of activity lost; paper records cover the gap.
Overload (too many users)Add access points; move the hub to a bigger machine; ask people to use text, not photos.
Theft or seizure of the hubRestore on another machine from the second-drive backup.

Restore, step by step

  1. Extract hub-config-<date>.tar into the hub folder and hub-certs-<date>.tar into CERT_DIR. On a computer with different drive paths, change CERT_DIR and ZIM_DIR in hub.env before you start.
  2. Start everything once, then stop the proxy and the app (docker stop hub-proxy hub-app) so nobody uses the empty hub.
  3. Restore the database from the app's own dump, as its documentation describes. Use a raw volume copy only for volumes whose containers were stopped during the backup: stop the container, empty the volume and extract (docker run --rm -v <volume>:/data -v <backup folder>:/backup alpine:3 sh -c 'find /data -mindepth 1 -delete && tar -C /data -xf /backup/vol-<volume>-<date>.tar').
  4. Restore the mail and webmail volumes the same way, with those containers stopped.
  5. On a new computer: install WireGuard. Import the hub tunnel file from the sealed admin envelope. Keep the filled tunnel file and its key files outside the hub folder, because backup.sh and kit-copy.sh copy the whole hub folder. Update the router's DHCP reservation for the new Ethernet port.
  6. Start everything again with the full compose command (with the mail file if street email is set up), and run the morning check (section 16.9).

16.12 Rehearsal before relying on it

Nothing in this plan should be trusted until it has run once end to end with the internet unplugged. Run this rehearsal as soon as the hardware arrives, and again every three months. Record results in the Decisions Book.

#TestPass when
1Restore from the external drive only, on a second computer (or, on the live hub, only after a fresh backup): remove the hub containers, volumes and images, unplug the internet, docker load, start, then restore last night's backup ("Restore, step by step")All containers show "Up" in docker ps in under 15 minutes, and accounts, messages and files are back
2Start the community app with the internet unplugged; watch its logsNo errors from failed outside calls
3iPhone, Android, Windows laptop, Mac: join, open https://hub.example.org (the hub address)Padlock, no warning, front page, on all four
4Register, have an admin approve the account, sign in with a password, sign out, sign in againWorks with no mail needed
5Which app features send mail: note each in MailpitList recorded; each code reaches the user via the desk
6Two accounts exchange messages (end-to-end encrypted, if the app has it); live updates arriveMessages arrive within seconds on both
7Upload an image; view it from another deviceThe image appears on the second device
8Create one group or channel for each working group (section 16.8)All work; note anything that fails offline
9An administrator resets a user's password at the desk; the user signs in with the new passwordWorks with no mail needed
10Library and start page; APK install on an Android phone from info/apps/Pages open; app installs and runs
11Phase 2, on the second computer (or on the live hub at a quiet hour, after a notice): copy the public fullchain.pem and privkey.pem aside; install the CA on four test devices; switch certificates; repeat test 3All four open the hub with a padlock. To switch back: copy the public files into CERT_DIR again and restart hub-proxy (and hub-mailserver if street email is set up)
12Power: run hub, router and one repeater from the 12 V battery for 12 hours on the watt meterMeasured consumption recorded; budget updated
13Coverage walk; repeater placementTwo bars or more along the whole street
14Load: 20 phones browsing and messaging at oncePages load in under 3 seconds
14aSign-in limits: 30 sign-ins from different phones within 10 minutes (the registration desk on a busy day)Nobody is locked out. If the app sees one address for every phone (common when Docker runs inside a virtual machine, as on Windows and macOS), the app's sign-in limits for each address then apply to the whole street at once: raise them if anyone is locked out, and record the values.
14bSwitch the app off: is the static notices page in info/ still reachable?Notices readable while the app is down
15Backup and restore: run the app's backup, restore into a scratch Docker setupData and files come back intact
16Starlink (if available): router in repeater mode; hub stays local; per-device limit worksHub unaffected; outside internet shared as set
17Failover: swap in the spare router; move the hub to a second machineBack in service within targets
18Neighbourhood link: from a phone in neighbourhood A, open neighbourhood B's start page by its IP address; send mail between the hubsPage opens; mail arrives; neither router hands out addresses in the other's range

Open questions that only the rehearsal can answer: which app features send mail; whether anything calls an outside service and waits on it; real power draw; Wi-Fi range on your street.

16.13 Timeline and costs

WhenTask
Week 1Buy the hardware (section 16.4.1: about 900 to 1,700 GBP for the full set; about 500 GBP for a minimum set: router, spare, battery, charger, USB-C chargers, fuses, a USB-C Ethernet hub and a cable). Choose the community app: test two or three open-source candidates in the rehearsal (for example Zulip or Mattermost for chat, Discourse for a forum).
Week 1DNS token; phase 1 certificate; DNS records; a renewal reminder every two weeks.
Week 2Pull and pin images; save the image archive; download the library, Android apps and installers.
Week 2Create the local certificate authority (make-local-ca.sh); store its key offline.
Week 3Configure routers, repeaters and bridges; wire the 12 V system; print posters.
Week 3Full rehearsal (section 16.12); fix; record.
Every two weeksRenew the certificate. Monthly: re-run a short rehearsal (tests 1, 3, 4, 6).

Notes

  1. Mozilla Developer Network, "Secure contexts" (Web Crypto and other features available only over HTTPS). https://developer.mozilla.org/en-US/docs/Web/Security/Secure_Contexts (accessed 14 November 2026). Back to text
  2. The Register, "Apple, Google agree to loosen grip on UK app stores", February 2026. https://www.theregister.com/2026/02/10/apple_google_uk_app_stores/ (accessed 14 November 2026). Back to text
  3. Apple, "Create an ad hoc provisioning profile" and "Distribute to registered devices", Xcode Help. https://help.apple.com/xcode/mac/current/en.lproj/dev4335bfd3d.html (accessed 14 November 2026). Back to text
  4. Mozilla Developer Network, "Web Bluetooth API" (browser compatibility: not supported in Safari on iOS). https://developer.mozilla.org/en-US/docs/Web/API/Web_Bluetooth_API (accessed 14 November 2026). Back to text
  5. OpenWrt, "DNS and DHCP configuration". https://openwrt.org/docs/guide-user/base-system/dhcp (accessed 14 November 2026). Back to text
  6. lego ACME client, "Cloudflare" DNS provider documentation. https://go-acme.github.io/lego/dns/cloudflare/ (accessed 14 November 2026). Back to text
  7. DNSimple, "SSL Certificate Validity Changes (2026 to 2029)" (CA/Browser Forum ballot SC-081). https://support.dnsimple.com/articles/announcement-ssl-certificate-validity-changes/ (accessed 14 November 2026). Back to text
  8. DNSimple, "SSL Certificate Validity Changes (2026 to 2029)" (CA/Browser Forum ballot SC-081). https://support.dnsimple.com/articles/announcement-ssl-certificate-validity-changes/ (accessed 14 November 2026). Back to text
  9. Apple, "Requirements for trusted certificates in iOS 13 and macOS 10.15". https://support.apple.com/en-us/103769 (accessed 14 November 2026). Back to text

Chapter 17Community email and relay

For the Communications and Network Lead and technical helpers. Builds on Chapter 16.

What this chapter decides

  • Every person on the street network gets a personal email address that works with the phone's built-in Mail app or a web browser, with nothing to install.
  • Each neighbourhood hub runs a small mail server holding a subdomain for each of its streets. Mail between neighbourhoods travels over the outdoor Wi-Fi links. Mail to and from the rest of the world travels, whenever a satellite link is up, through an anchor relay on a server outside the affected area.
  • Mail is store and forward: when any link is down, messages wait in queues and move on when it returns.
  • Email does not travel over Bluetooth. Phone-to-phone Bluetooth messaging (BitChat) carries short texts nearby; email needs the Wi-Fi network.

17.1 Why email, and why it works without internet access

Email is the one messaging system that every phone and computer already supports without installing anything, that gives each person a lasting address, and that was designed from the start to hold messages and pass them on when a connection becomes available. Normal email fails in a blackout because people's mail is held by large providers on the internet. The answer is to run mail locally: a mail server on each hub holds the mailboxes of the streets it serves, so mail between people on the network works with no outside connection at all.

17.2 Can email run over Bluetooth?

No, not in a useful way. Email needs a server that stores mailboxes and is always on, and it carries far more data than a Bluetooth mesh can move. Bluetooth reaches only a few tens of metres between phones210, and phones limit it in the background. The plan therefore uses each technology for what it does well:

NeedCarried by
Short texts to people nearby, even away from the street networkBitChat over Bluetooth (section 15.4)
Personal addresses, longer messages, attachments, messages that wait for the personEmail on the hub, over Wi-Fi (this chapter)
Group coordination, notices, rotas, planningThe community app on the hub (section 16.8)
Messages between neighbourhoodsEmail over outdoor Wi-Fi links; short texts over LoRa radios (section 15.6)
Messages to the outside worldEmail through the anchor relay when a satellite link is up

17.3 Design

Neighbourhood A hubmail server + webmailmailboxes:sam@streeta.example.orgphones: Mail app or browser Neighbourhood B hubmail server + webmailmailboxes:alex@streetb.example.orgphones: Mail app or browser Wi-Fi link: directhub-to-hub delivery Anchor relaysmall server outside theaffected area; public MX;signs and queues mailfor every street encrypted tunnel over Starlink, opened from the hub when the link is up the internet Every arrow is store and forward: if a link is down, mail waits in the sender's queue and moves on when it returns.
Figure 17.1. Community email. Each neighbourhood hub holds the mailboxes of its streets. Hubs pass mail directly over the routed Wi-Fi link between neighbourhoods. The anchor relay connects every street to the rest of the world when any satellite link is up.

17.4 Set up your hub mail server (prepare now)

  1. Choose the domain and the street subdomains. Publish, at the DNS provider, MX records for each street subdomain pointing at the anchor relay, plus the SPF, DKIM and DMARC records the relay's mail server generates. Example records: mail/dns-records.example.txt.
  2. Pull and pin the mail server and webmail images and save them in the image archive (section 16.7).
  3. Add both services with mail/docker-compose.mail.yml, started together with the hub's own compose file. The webmail page goes behind Caddy at mail.<hub address> (for example mail.hub.example.org). The Caddyfile already has this route. The mail server's ports (25 from other hubs and the relay, 465 or 587 for sending, 993 for reading) reach only the street network and the tunnel.
  4. Mail server settings (in its admin page, on port 8080 of the hub computer only): add every street subdomain this hub holds, and the role addresses; load the hub's certificate files from /certs; add one route for each subdomain held by another neighbourhood's hub, pointing at that hub's address on port 25; send all other outgoing mail through the relay at 10.77.0.1 on port 25; and set the queue retry as in step 7. With no internet, set the mail server's SPF, DKIM, DMARC and reverse-DNS checks to relaxed or off for mail from the street network, or each message waits on DNS look-ups that cannot succeed. If the hub runs Docker Desktop (macOS or Windows), Docker hides each phone's own address, so the mail server sees every phone as one address: turn off the mail server's automatic blocking of addresses after failed sign-ins (keep the limit per account), or run the mail server directly on the hub computer instead of in Docker. Write each setting down on the admin sheet.
  5. Certificates: the mail server uses the same certificate files as the hub, covering mail.<hub address> as well as the hub address, so the phase 1 and phase 2 plan in section 16.6 covers mail too.
  6. Local addresses: add the mail address to the router's DNS line (it is already covered if the line answers every address under the hub address).
  7. Limits: set a mailbox size (for example 200 MB each), a message size limit (for example 10 MB), and queue retry for at least 14 days, so that mail waits through long link failures instead of bouncing.
  8. Accounts: created by an administrator at the welcome desk, with the person choosing their own password. Write nothing down for them except the address.
  9. Rehearse (section 17.9).

17.5 Connect phones and computers (nothing to install)

17.6 Anchor relay

17.7 Security and privacy

17.8 Power and capacity

The mail server and webmail together need a few hundred megabytes of memory and very little power. A street of several hundred people fits easily on the same hub as the community app.

17.9 Rehearsal tests

#TestPass when
0Run mail/mail-test.sh from a laptop on the street networkThe hub accepts the message and the mailbox answers
1Add an account on an iPhone's built-in Mail app and on Android, with the internet unpluggedBoth send and receive within the street
2Webmail from a laptopWorks with a padlock, no warning
3Mail from neighbourhood A's hub to neighbourhood B's hub over the routed link; then cut the link for an hourDelivered at once; during the cut, queued and delivered when the link returns
4Connect a satellite link; send to and receive from an outside addressBoth directions work through the relay; outside providers accept the mail
5Role address after a change of role holderMail reaches the new holder
6Restore the mail server from backupMailboxes come back intact
7Stop the relay for a day; send mail to an outside address and from oneBoth wait in their queues and are delivered when the relay returns
8Try to send through the relay from an address outside the tunnelRefused (the relay is not an open relay)
9Enter a wrong password 5 times on one phone; then sign in from other phonesOther phones still sign in (one phone's mistakes do not block the street)
10Webmail after the switch to the street's own certificate (phase 2)Webmail still signs in and sends
11Stop relay 1; on the hub turn off tunnel 1 and turn on tunnel 2; change relay 2's routes to the hub tunnel addresses; send to the street from an outside address and from the street to an outside address; afterwards reverse all three changesBoth arrive through relay 2 and pass the receiver's checks
12With the settings in section 17.11: the community app sends a code to an outside address with no satellite linkThe code waits in the mail server's queue, and leaves when a link is up
13After the switch to the street's own certificate: the built-in Mail app on iPhone and on AndroidThe iPhone Mail app connects. Each Android mail app tested is recorded as working or refused; users of refused apps are told to use webmail in Chrome

17.10 Should your street build its own app?

No: section 15.8 and section 16.2.3 give the reasons, so put the effort into the hub, the mail service and the relay, and ask everyone to install BitChat and Delta Chat now.

17.11 Community app mail and hub mail

If the community app sends sign-up notices or codes by email, point its mail settings (SMTP host and port) at the hub's own mail server and register people with their street mail address. Codes then arrive in each person's own mailbox, so no administrator needs to read them. Create a mail account for the app (for example noreply@ a street subdomain). Give the app that address and password, with host mail.<hub address> and port 587 (STARTTLS) or 465 (TLS); the hub certificate covers that address. Keep a mail catcher such as Mailpit only as a fallback during setup.

Notes

  1. Bluetooth SIG, "Understanding Bluetooth range" (range depends on the radio, the antenna and obstacles). https://www.bluetooth.com/learn-about-bluetooth/key-attributes/range/ (accessed 14 November 2026). Back to text
  2. Stalwart Labs, "Stalwart Mail Server" (SMTP, IMAP and JMAP in one program). https://stalw.art/ (accessed 14 November 2026). Back to text
  3. Roundcube webmail. https://roundcube.net/ (accessed 14 November 2026). Back to text
  4. WireGuard. https://www.wireguard.com/ (accessed 14 November 2026). Back to text
  5. DishyTech, "Guide: Starlink Port Forwarding and Workarounds" (home plans use carrier-grade NAT; the Starlink router does not forward ports). https://www.dishytech.com/does-starlink-have-port-forwarding/ (accessed 14 November 2026). Back to text
  6. Apple, "Add email accounts to your iPhone" (iPhone User Guide). https://support.apple.com/guide/iphone/ (accessed 14 November 2026). Back to text
  7. Stalwart Labs, "Stalwart" documentation (system requirements and configuration). https://stalw.art/docs/ (accessed 14 November 2026). Back to text
  8. Delta Chat (end-to-end encrypted messaging over email). https://delta.chat/ (accessed 14 November 2026). Back to text
  9. Delta Chat project, "chatmail relay: technical overview". https://chatmail.at/doc/relay/overview.html (accessed 14 November 2026). Back to text

Chapter 18Warmth, shelter and safety in detail

In a winter blackout in a cold climate, cold and carbon monoxide are the two biggest dangers. Both are preventable.

18.1 Staying warm at home

  1. Choose one room to live in: the smallest room with the fewest outside walls, ideally facing the winter sun (south in the northern hemisphere, north in the southern). Move everyone and their bedding there.
  2. Stop draughts. Close internal doors. Roll towels against the bottom of doors. Hang blankets or duvets over doors and windows. Cover windows with bubble wrap or cling film for an extra layer. Close curtains at night; open them on sunny days.
  3. Dress in layers, including a hat, socks and fingerless gloves indoors. Several thin layers trap more warmth than one thick one.219 Keep clothes dry.
  4. Sleep together in one room, off the floor if possible, with extra blankets underneath as well as on top.
  5. Hot water bottles: fill two-thirds with hot (not boiling) water from the stove, squeeze out the air, check the stopper. Replace bottles more than two years old (the date is on the "flower" mark).220
  6. Eat and drink warm food and drinks, and eat regularly: the body needs fuel to make heat.
  7. Move for a few minutes every hour.

18.2 Street warm room

The Warmth and Shelter Lead finds one or two homes that can stay warm: a house with a gas fire that needs no electricity, a wood burner, an open fireplace in good order, or a gas boiler that can run from an electric car or power station (section 14.3). Older people, babies, people who are ill and anyone whose home is too cold spend the day there in turns. People using home oxygen sit well away from any flame or fire (section 20.2). Ukraine's "Invincibility Points" (heated rooms with power, water and internet) show how much one warm room can do for morale as well as health.221

18.3 Hypothermia

Signs: shivering (older people may not shiver), pale cold skin, slurred speech, confusion, clumsiness, drowsiness, slow breathing. A person with hypothermia often does not realise it.222

What to do: move them to the warmest place; replace wet clothes with dry; wrap them in blankets, including the head; give warm sweet drinks if they are fully awake (no alcohol); share body warmth. Do not put them in a hot bath, do not use a hot water bottle or heat lamp on them, and do not rub their arms, legs, hands or feet. Hypothermia is a medical emergency: get help at once (the emergency number, if any phone works), and keep the person awake.223

18.4 Carbon monoxide

Warning. Never use any of these indoors, in a garage, tent, shed or near open windows: petrol or diesel generators, barbecues (charcoal or gas), patio heaters, camping heaters, camping stoves (for any use), engines of any kind. Never heat a room with a gas cooker or oven.224 Barbecue charcoal gives off deadly fumes even after it stops glowing.

Symptoms are like flu without a high temperature: headache, dizziness, sickness, tiredness, confusion, breathlessness. Suspect carbon monoxide when other people in the same place have the same symptoms.225226 Act at once: get everyone into fresh air, turn off the source if safe, and do not go back in until someone has given you advice. Get emergency help (section 20.3) for anyone who finds it hard to breathe, is suddenly confused or weak, has chest pain or is unconscious. If a gas appliance may be the cause, call the gas emergency number (in Great Britain 0800 111 999, in Northern Ireland 0800 002 001). Fit a battery carbon monoxide alarm in every room where anything burns.

18.5 Fires, gas and fireplaces

18.6 Heat and hot climates

If a blackout comes in a heatwave or in a hot climate, heat becomes the danger, especially for older people, babies, and people with heart or lung conditions. Keep curtains closed on the sunny side, open windows at night, drink regularly, use cool damp cloths, stay out of the midday sun, and check on vulnerable neighbours twice a day.

Heat exhaustion shows as tiredness, dizziness, headache, feeling sick, heavy sweating with pale clammy skin, cramps, a high temperature and great thirst. Move the person to a cool place, remove extra clothing, give plenty of water or oral rehydration solution (section 13.12), and cool the skin with water, a fan, and cold packs wrapped in cloth under the armpits or on the neck. They should feel better within 30 minutes. If they do not, or if they have hot skin that is not sweating, fast breathing, confusion, a fit or loss of consciousness, it is heatstroke: get emergency help (section 20.3) and keep cooling them.232

18.7 Keeping homes safe

18.8 Flats and tall buildings

18.9 Pipes in empty or unheated homes

In a long winter outage, water pipes in unheated homes can freeze and burst, flooding the home when water returns. If a home will stay unheated, turn off the stopcock and open the taps to drain the pipes, and collect the water (section 13.2); leave a note on the stopcock. Turn the water back on only when someone can check for leaks.

18.10 If you must leave home: rest centres

If a home becomes unsafe (cold, fire, flood, structural damage), people go first to the street's warm room or a neighbour. In a wider emergency, local authorities often open rest centres (often in leisure centres, schools or community halls) with warmth, food and first aid. Listen to local radio for their locations, and send a runner to the local authority if none are announced. Take the grab bag, medicines, documents, phone and charger, and tell the Records and Resources Keeper where you are going.

18.11 Fires with no fire brigade

Candles, stoves, generators and heaters make fires more likely in a blackout, and with no phones the fire brigade may not be called in time. The official rule still applies: get out, stay out, and do not tackle a fire yourself except a very small one that is blocking your way out.233

  1. Prevent: torches instead of candles; any candle on a plate, away from curtains, never left alone; stoves and generators outdoors only; no drying clothes near heaters.
  2. Equip: record fire extinguishers, fire blankets and ladders on the Asset Door Card (form 2). Keep a fire blanket and a bucket of sand near any cooking point. Never throw water on a pan fire.
  3. If a fire starts: shout "Fire!", get everyone out, close doors behind you, and meet outside. If clothes catch fire: stop, drop and roll, and smother the flames with a coat or blanket.234
  4. Raise the alarm: give the help signal (three short whistle blasts, repeated), then a runner to the Street Coordinator and to the nearest fire station or police point if roads are open; try the emergency number from any phone that has a signal.
  5. Protect neighbours: in terraced (row) and semi-detached (paired) houses, fire spreads through roofs. Wake the houses on both sides at once and get them out too. Turn off the gas at the meter of the burning house only if it is safe to reach.
  6. Never go back in, and never fight a fire inside a building. A bucket chain from water butts is only for small fires outdoors (a shed, a fence, a bin) and to wet a neighbouring fence or wall, from a safe distance.
  7. Afterwards: the Welcome and Safety Lead keeps people out of the damaged house and records the event in the Incident Log, and the Warmth and Shelter Lead finds the family a room.

Notes

  1. UK Health Security Agency and Age UK, "Top tips for keeping warm and well this winter" (heat the rooms you use to at least 18°C; several layers). https://assets.publishing.service.gov.uk/media/64fb2e2157e8840013e127ac/winter-leaflet-v3.pdf (accessed 14 November 2026). Back to text
  2. BSI, "New BSI committee to review and update hot water bottle specification" (BS 1970; date marks on hot water bottles), May 2025. https://www.bsigroup.com/en-IE/insights-and-media/media-centre/press-releases/2025/may/bsi-announces-new-committee-to-review-and-update-hot-water-bottle-specification (accessed 14 November 2026). Back to text
  3. Hromadske, "Invincibility points in Kyiv: what has been achieved and what needs to be worked out", 2022. https://hromadske.ua/en/posts/invincibility-points-in-kyiv-what-has-been-achieved-and-what-needs-to-be-worked-out-photo-report (accessed 14 November 2026). Back to text
  4. NHS, "Hypothermia". https://www.nhs.uk/conditions/hypothermia/ (accessed 14 November 2026). Back to text
  5. NHS, "Hypothermia". https://www.nhs.uk/conditions/hypothermia/ (accessed 14 November 2026). Back to text
  6. US Centers for Disease Control and Prevention, "About Carbon Monoxide Poisoning" (generators more than 20 feet, about 6 metres, from windows, doors and vents; never heat a house with a gas oven). https://www.cdc.gov/carbon-monoxide/about/index.html (accessed 14 November 2026). Back to text
  7. NHS, "Carbon monoxide poisoning". https://www.nhs.uk/conditions/carbon-monoxide-poisoning/ (accessed 14 November 2026). Back to text
  8. NI Direct, "Carbon monoxide poisoning" (like flu but no high temperature; suspect it when others have similar symptoms). https://www.nidirect.gov.uk/conditions/carbon-monoxide-poisoning (accessed 14 November 2026). Back to text
  9. Energy Networks Association, "Smell gas?" (National Gas Emergency Service, 0800 111 999). https://www.energynetworks.org/customers/smell-gas (accessed 14 November 2026). Back to text
  10. US Centers for Disease Control and Prevention, "About Heat and Your Health" (signs of heat illness; people at higher risk; use fans only below 90°F; many medicines cause dehydration or overheating; plan for medicines that need cool storage). https://www.cdc.gov/heat-health/about/index.html (accessed 16 November 2026). Back to text
  11. US Centers for Disease Control and Prevention, "About Heat and Your Health" (signs of heat illness; people at higher risk; use fans only below 90°F; many medicines cause dehydration or overheating; plan for medicines that need cool storage). https://www.cdc.gov/heat-health/about/index.html (accessed 16 November 2026). Back to text
  12. US Centers for Disease Control and Prevention, "About Heat and Your Health" (signs of heat illness; people at higher risk; use fans only below 90°F; many medicines cause dehydration or overheating; plan for medicines that need cool storage). https://www.cdc.gov/heat-health/about/index.html (accessed 16 November 2026). Back to text
  13. World Health Organization, "Dengue" fact sheet, 21 August 2025 (cover, empty and clean domestic water storage containers every week). https://www.who.int/news-room/fact-sheets/detail/dengue-and-severe-dengue (accessed 16 November 2026). Back to text
  14. NHS, "Heat exhaustion and heatstroke". https://www.nhs.uk/conditions/heat-exhaustion-heatstroke/ (accessed 14 November 2026). Back to text
  15. UK Government, "Fire safety in the home" (get out, stay out; do not tackle fires yourself; extinguishers only for very small fires; stop, drop and roll). https://www.gov.uk/government/publications/make-your-home-safe-from-fire/fire-safety-in-the-home-accessible-version (accessed 14 November 2026). Back to text
  16. UK Government, "Fire safety in the home" (get out, stay out; do not tackle fires yourself; extinguishers only for very small fires; stop, drop and roll). https://www.gov.uk/government/publications/make-your-home-safe-from-fire/fire-safety-in-the-home-accessible-version (accessed 14 November 2026). Back to text

Chapter 19Food in detail

19.1 Eating order

  1. Fridge first. Food in a closed fridge stays safe for about 4 hours.235 After that, eat or cook perishable food (meat, fish, dairy, cooked leftovers) quickly or throw it out.
  2. Freezer next. A full freezer kept shut stays frozen for about 48 hours; a half-full one about 24 hours.236
  3. Cupboard last. Tins, dried food, packets.

In cold weather (below 5°C, the temperature a fridge keeps), a cool box or lidded crate outside in the shade, safe from animals, works as a fridge.237 When in doubt, throw it out, especially meat, fish, dairy and cooked rice.

19.2 Cooking without electricity

POT Pot sits on a metal grill or three small stones, leaving a gap of about 2 cm for the hot gases. Chimney: an insulated upright channel. Hot gases rush up, pulling air in through the feed opening. Feed opening at the bottom front: push small dry sticks in from the side, feeding more as they burn. Build from about 16 bricks or concrete blocks laid without mortar, in an L-shape as shown, on bare ground or paving, outdoors, away from buildings. Small dry fuel, a hot fire, and little smoke.
Figure 19.1. Brick rocket stove in cross-section. The dotted area is the L-shaped burning channel. A large tin can with a smaller tin inside, packed with sand or soil, works on the same principle.

19.3 Babies, special diets and pets

19.4 Shared kitchen (longer outages)

19.5 Street food stocktake and rations

If the outage may last more than a week, the Food Lead counts what the street has, so that nobody runs out while others waste food.

  1. Day 3: stocktake. With each household's consent, list the food it can share and the food it needs, by kind (tins, dried, fresh, baby food, special diets). Households keep their own food; the list is for planning.
  2. Count the need. An average woman needs about 2,000 kcal a day and an average man about 2,500; children need less, and people doing hard physical work need more.243 For planning, use 2,000 kcal per person per day.
  3. Count the days. Days of food = total kcal in the stocktake ÷ (people × 2,000). Packets show kcal per 100 g; a rough guide is about 330 kcal for a 415 g tin of baked beans and about 3,500 kcal for 1 kg of dried rice or pasta (the label shows about 350 kcal per 100 g).244
  4. If it is under 14 days, the Food Lead proposes a sharing rule (a weighted vote, section 12.5): fresh and chilled food first, a shared hot meal once a day from the shared kitchen, and priority for babies, children, pregnant and breastfeeding women, older people and anyone ill.
  5. Record what goes into and out of the shared stores in the Shared Stores Ledger (form 8), and repeat the count every 3 days.

Notes

  1. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  2. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  3. Food Standards Agency, "Food safety in a power cut: advice for consumers", updated September 2025. https://www.gov.uk/government/publications/food-safety-in-a-power-cut-advice-for-consumers/food-safety-in-a-power-cut-advice-for-consumers (accessed 14 November 2026). Back to text
  4. Aprovecho Research Center, retained heat cookers (test results: about 50% of fuel and cooking time saved). https://aprovecho.org/category/biomass-alternatives/ (accessed 14 November 2026). Back to text
  5. GIZ, "Report: Performance Test of retained heat cooker (WonderBag)", energypedia. https://energypedia.info/images/a/af/Report_Performance_Test_of_retained_heat_cooker_%28WonderBag%29_GIZ.pdf (accessed 14 November 2026). Back to text
  6. NHS, "How to make up baby formula". https://www.nhs.uk/baby/breastfeeding-and-bottle-feeding/bottle-feeding/making-up-baby-formula/ (accessed 14 November 2026). Back to text
  7. NHS, "Sterilising baby bottles" (boil for at least 10 minutes). https://www.nhs.uk/baby/breastfeeding-and-bottle-feeding/bottle-feeding/sterilising-baby-bottles/ (accessed 14 November 2026). Back to text
  8. Royal Horticultural Society, "How to grow potatoes" (first earlies can be ready in as little as 12 weeks; maincrops later). https://www.rhs.org.uk/vegetables/potatoes/grow-your-own (accessed 14 November 2026). Back to text
  9. NHS, "Understanding calories" (an average man needs 2,500 kcal a day, an average woman 2,000). https://www.nhs.uk/live-well/healthy-weight/managing-your-weight/understanding-calories/ (accessed 14 November 2026). Back to text
  10. Heinz Beanz 415 g, nutrition label (about 330 kcal a tin), as listed by a UK supermarket. https://www.tesco.com/groceries/en-GB/products/254656543 (accessed 14 November 2026). Back to text

Chapter 20Health and care in detail

20.1 Medicines

20.2 People on powered medical equipment

Warning: oxygen and flames. Oxygen makes fires start easily and burn fiercely. Keep anyone using home oxygen, and their cylinders and concentrator, at least 3 metres from any naked flame, gas fire, wood burner or cooker, and at least 1.5 metres from heaters and radiators (or further if the oxygen supplier advises). No smoking in any room where oxygen is used.247
EquipmentPrepare nowIn the blackout
Home oxygen concentratorAsk your oxygen supplier for backup cylinders and their emergency number. Join your energy supplier's priority list (in Great Britain, the Priority Services Register).Use backup cylinders (ask the oxygen supplier how long they last). Top priority for the electric car or power station (100 to 350 W; the figure is on its label).
CPAPAsk your sleep clinic whether you can safely miss nights. Buy a 12 V adapter or battery pack for your model.Run from a 12 V battery or power station; skip the heated humidifier to save power.
Home dialysisAsk your renal unit for its emergency plan now.Follow that plan. Contact the unit as early as possible.
Ventilators, suction, feeding pumpsAgree an emergency plan with the care team; know battery run times.Highest priority for power.
Electric beds, hoists, stairliftsKnow the manual lowering method.Plan where the person will sleep and how they will move.

20.3 First aid essentials

These basics follow standard first aid guidance, as published by UK health services and the Resuscitation Council UK; your own country's guidance may differ in detail. A first aid course is one of the best preparations anyone can make.

Getting help when phones do not work

20.4 Preventing illness

20.5 Mental health

Uncertainty, darkness, cold and worry wear people down. What helps most is what the plan already provides: a daily routine, a role, regular contact with others and honest information. Watch for people who withdraw, stop eating or sleeping, or talk of hopelessness, and make sure someone sits with them.264 Keep children's days structured with play, learning and jobs they can be proud of.

20.6 Skills

The census records everyone with medical or care skills (doctors, nurses, paramedics, carers, pharmacists, midwives, vets, first aiders, counsellors). The Health and Care Lead organises them into a rota, and the neighbourhood council shares them between streets.

20.7 When someone dies

In a long emergency, someone on the street may die when no doctor, ambulance or undertaker can come. Treat the person and the family with dignity.

Notes

  1. NHS, "How to order a repeat prescription" (request it up to 5 working days before you need it). https://www.nhs.uk/nhs-services/online-services/how-to-order-a-repeat-prescription/ (accessed 14 November 2026). Back to text
  2. US Food and Drug Administration, "Information Regarding Insulin Storage and Switching Between Products in an Emergency". https://www.fda.gov/drugs/emergency-preparedness-drugs/information-regarding-insulin-storage-and-switching-between-products-emergency (accessed 14 November 2026). Back to text
  3. NHS, "Home oxygen treatment" (keep at least 3 metres from open flames and 1.5 metres from heat sources). https://www.nhs.uk/tests-and-treatments/home-oxygen-treatment/ (accessed 14 November 2026). Back to text
  4. Resuscitation Council UK, "Adult basic life support guidelines", 2025. https://www.resus.org.uk/library/2025-resuscitation-guidelines/adult-basic-life-support-guidelines (accessed 14 November 2026). Back to text
  5. British Heart Foundation, "The Circuit: the national defibrillator network" (999 call handlers give access codes). https://www.bhf.org.uk/how-you-can-help/how-to-save-a-life/defibrillators/national-defibrillator-network-the-circuit (accessed 14 November 2026). Back to text
  6. Resuscitation Council UK, "Paediatric basic life support guidelines", 2025. https://www.resus.org.uk/library/2025-resuscitation-guidelines/paediatric-basic-life-support-guidelines (accessed 14 November 2026). Back to text
  7. St John Ambulance, "Recovery position" (via the NHS page). https://www.nhs.uk/conditions/first-aid/recovery-position/ (accessed 14 November 2026). Back to text
  8. Resuscitation Council UK, "First aid guidelines", 2025 (bleeding, tourniquets, burns, choking). https://www.resus.org.uk/library/2025-resuscitation-guidelines/first-aid-guidelines (accessed 14 November 2026). Back to text
  9. NHS, "Burns and scalds" (cool for 20 minutes; cling film; no creams, oils or butter). https://www.nhs.uk/conditions/burns-and-scalds/ (accessed 14 November 2026). Back to text
  10. Resuscitation Council UK, "First aid guidelines", 2025 (bleeding, tourniquets, burns, choking). https://www.resus.org.uk/library/2025-resuscitation-guidelines/first-aid-guidelines (accessed 14 November 2026). Back to text
  11. Resuscitation Council UK, "Paediatric basic life support guidelines", 2025. https://www.resus.org.uk/library/2025-resuscitation-guidelines/paediatric-basic-life-support-guidelines (accessed 14 November 2026). Back to text
  12. NHS, "Stroke: symptoms" (FAST). https://www.nhs.uk/conditions/stroke/symptoms/ (accessed 14 November 2026). Back to text
  13. NHS, "Heart attack". https://www.nhs.uk/conditions/heart-attack/ (accessed 14 November 2026). Back to text
  14. NHS, "Anaphylaxis". https://www.nhs.uk/conditions/anaphylaxis/ (accessed 14 November 2026). Back to text
  15. NHS, "What to do if someone has a seizure (fit)". https://www.nhs.uk/symptoms/what-to-do-if-someone-has-a-seizure-fit/ (accessed 14 November 2026). Back to text
  16. NHS, "Broken arm or wrist" (support the injury; make a sling). https://www.nhs.uk/conditions/broken-arm-or-wrist/ (accessed 14 November 2026). Back to text
  17. NHS, "Head injury and concussion". https://www.nhs.uk/conditions/head-injury-and-concussion/ (accessed 14 November 2026). Back to text
  18. NHS, "Sepsis". https://www.nhs.uk/conditions/sepsis/ (accessed 14 November 2026). Back to text
  19. European Commission, "112: the EU's emergency phone number" (free of charge from fixed and mobile phones everywhere in the EU). https://digital-strategy.ec.europa.eu/en/policies/112 (accessed 16 November 2026). Back to text
  20. World Health Organization, War Trauma Foundation and World Vision International, Psychological First Aid: Guide for Field Workers, 2011. https://www.who.int/publications/i/item/9789241548205 (accessed 14 November 2026). Back to text
  21. Scottish Government, "Fatal Accident Inquiries: review" (in Scotland, doctors and the police report deaths to the procurator fiscal). https://www.gov.scot/publications/thematic-review-fatal-accident-inquiries/pages/4/ (accessed 14 November 2026). Back to text
  22. UK Government, "What to do after someone dies". https://www.gov.uk/after-a-death (accessed 14 November 2026). Back to text

Chapter 21Local AI, LoRA and offline library

For whoever looks after the street's computers. Model facts were checked on 14 November 2026; this field changes monthly, so check again before downloading.

Summary

  • Best open model for one machine today: Qwen3.8-27B (Alibaba, released August 2026, Apache-2.0 licence, 27 billion parameters, reads text and images, 262,000-token context). It is the strongest published open model for one computer with 32 to 64 GB of memory.267
  • On a basic 8 GB laptop, Qwen3.8-27B does not fit. The best model that does is Gemma 4 E4B (Google, Apache-2.0, 8 billion stored parameters: about 4 GB of weights at 4-bit, about 5 GB in use)268: good for questions, summaries and drafting, weak for serious coding.
  • Ideal hardware: a computer with 64 GB of memory (for example an Apple silicon laptop, or a Windows or Linux computer with a large graphics card) runs Qwen3.8-27B at high quality, plus a fast second model and a medical model. 32 GB is the minimum for Qwen3.8-27B at 4-bit.
  • LoRA is a way to teach an existing model a narrow skill with a small add-on file. There are no trusted, published LoRA adapters for any common programming language or for blackout needs. A community can train its own adapter on its own documents while the internet and plenty of power exist (section 21.6); section 21.5 explains LoRA in full.
  • Pair the model with the offline library (Wikipedia, medical encyclopedia, programming documentation, Stack Overflow). For facts, an AI that reads the right document beats one trained to remember it.

21.1 Models that matter (November 2026)

ModelSizeLicenceStrengthsRuns on
Qwen3.8-27B27B dense; visionApache-2.0Strongest general model for 32 to 64 GB;269 reasoning ("thinking" mode on by default, can be turned off); reads photos and screenshots; long context32 GB (4-bit, tight), 64 GB (8-bit, comfortable)
Qwen3.6-35B-A3B35B mixture-of-experts, 3B active for each tokenApache-2.0Very fast for its quality (only 3B parameters work at a time)27048 GB+ comfortable; 32 GB only at 3-bit
Gemma 4 E2B, E4B, 12B, 26B-A4B, 31BFrom phone size to 31BApache-2.0E4B runs on phones and 8 GB computers; 12B on 16 GB laptops; audio input on the small ones8 GB (E4B) to 32 GB (31B)
MedGemma 1.5 4B and 27BMedical fine-tunes of Gemma 3Gemma Terms of UseMedical questions and medical images (X-ray, skin, pathology)2718 GB (4B, tight) to 32 GB (27B, 4-bit)
Qwen3.8-Flash-Next125B MoE, 6B activeQwen Community LicenseSlightly stronger than the 27B, fast128 GB (check runtime support first)
GLM-5.3-Flash, DeepSeek-V4.1-Flash320B and 552B MoEMITNear-frontier256 to 512 GB workstations
Kimi K3, GLM-5.3, Qwen3.8-2.4T750B to 2.8TMixedFrontier open modelsData centres only

Benchmark figures are as published by the developers on their model cards and in the November 2026 rankings listed in the sources. Independent results vary.

21.2 What you need to run them

21.2.1 Rule of thumb

21.2.2 Hardware tiers

TierMachineWhat to runWhat it is good for
Basicany laptop with 8 GBGemma 4 E4B, 4-bit (about 5 GB), short context; or a 3 to 4B model (Qwen3 4B, Phi-4 Mini) at 20 to 35 tokens (word pieces) a second; MedGemma 1.5 4B for medical questions (load one at a time)Questions, explanations, summaries, translation, drafting notices, reading library pages. Not serious software development.
Minimum for large modelsApple silicon Mac with 32 GB (for example a Pro chip), or a Windows or Linux computer with a graphics card holding 24 GB or moreQwen3.8-27B at 4-bit (about 16.5 GB) with a modest context; or Gemma 4 26B-A4B for speedReal help with reasoning and long documents, slower; keep conversations short
IdealApple silicon Mac with 64 GB, ideally a Max chip (MacBook Pro) or Mac Studio; or a Windows or Linux computer with 64 GB and a large graphics card (more power-hungry)Qwen3.8-27B at 8-bit (about 29 GB) as the main model; Qwen3.6-35B-A3B at 4 to 6-bit as a fast second model; MedGemma 27B at 4-bit when needed (load one large model at a time)Strong help with reasoning; vision; long documents
Maximum128 GB or moreAdd Qwen3.8-Flash-Next; run several models at once; long contextsA small team's AI server

Power in a blackout: a laptop answering questions draws roughly 20 to 60 W while working (more on the fastest chips), and almost nothing when idle. A Mac Studio draws more. One hour of AI work is about one hour of pedalling. Laptops are the best choice for a blackout because they carry their own battery.

A PC alternative: a desktop with an NVIDIA graphics card of 24 GB (or two of 16 GB) runs Qwen3.8-27B at 4-bit fast, but draws 300 to 600 W, which is impractical on blackout power. An efficient laptop (for example Apple silicon) is the better choice here.

21.3 Software

ProgramWhat it isWhy you might want it
llama.cpp (open source, MIT)The engine most local AI tools are built on. Its llama-server serves a chat web page and an OpenAI-compatible API.Recommended for the street hub: any phone can use the AI in its browser at https://ai.hub.example.org. Loads LoRA adapters (--lora), several at once.
LM Studio (free app)A desktop app for Mac, Windows and Linux to download, run and chat with models.Easiest for most people. Runs GGUF and MLX models; shows whether a model fits your memory.
Ollama (open source)Simple command-line runner with a model library.Convenient; LoRA through an ADAPTER line (support depends on the model family).
MLX and mlx-lm (Apple, open source)Apple's machine learning framework.Fastest on Apple silicon, and can train LoRA adapters on a Mac.273
Kiwix (kiwix-serve, Kiwix desktop)Offline library server and reader.The library the AI and people both read.
whisper.cpp (optional)Speech to text, offline.Lets people who cannot type or read well speak questions.

Keep the installers themselves on the external drive, so any computer can be set up with no internet.

21.4 What to download now

Everything goes on a large external drive (1 TB or more), kept safe and encrypted. Record the source and SHA-256 checksum of every file in a list beside it.

21.4.1 Models

FileSourceApproximate sizeWhy
Gemma 4 E4B instruct, GGUF 4-bitGoogle's official release on Hugging Face, or a well-known quantiser's GGUF build of it5 GBRuns on an 8 GB machine
Qwen3 4B instruct, GGUF 4-bitQwen on Hugging Face2.5 GBLighter fallback for 8 GB
MedGemma 1.5 4B, GGUF 4-bitgoogle/medgemma (accept Google's terms on Hugging Face first)3 GBMedical questions on an 8 GB machine
Qwen3.8-27B, GGUF Q4_K_M and Q8_0Community quantisations of Qwen/Qwen3.8-27B by a well-known quantiser (official repository ships full weights only); check the card lists the official base16.5 + 29 GBFor the 32 GB and 64 GB tiers
Qwen3.8-27B original weights (safetensors, BF16)Qwen/Qwen3.8-27Babout 56 GBNeeded later to train or merge LoRA adapters and make new quantisations with no internet
Qwen3.6-35B-A3B, GGUF Q4_K_MQwen and community quantisersabout 21 GBFast second model for the ideal tier
MedGemma 27B text, GGUF 4-bitgoogle/medgemmaabout 17 GBBetter medical answers on the ideal tier
Whisper large-v3-turbo (whisper.cpp format), optionalggml-org on Hugging Face1.6 GBSpeech input

Total: about 150 GB. With the library below, the full set is about 300 to 450 GB of a 1 TB drive.

21.4.2 Library (Kiwix files, sizes from download.kiwix.org, November 2026)

FileSize274
wikipedia_en_all_maxi_2026-08 (with images) or wikipedia_en_all_nopic_2026-06 (no images)119 GB or 49 GB
wikipedia_en_medicine_maxi_2026-10 (WikiMed)1.7 GB
stackoverflow.com_en_all_2026-07107 GB
superuser, unix, electronics, diy, gardening Stack Exchange (2026-10)3.7, 1.2, 4.0, 1.9, 0.9 GB
ifixit_en_all_2025-123.3 GB
wikibooks_en_all_maxi_2026-10, wikivoyage_en_all_maxi_2026-094.4 GB, 1.0 GB
zimgit-post-disaster, -medicine, -water, -food-preparation, -knots615, 67, 20, 93, 27 MB
CAWST Biosand Filter Construction Manual (PDF, from resources.cawst.org)small

21.5 LoRA explained

21.5.1 What it is, in plain words

A large language model is a huge table of numbers (its "weights") learned from vast amounts of text. Changing all of them to teach the model something new ("full fine-tuning") needs data-centre hardware. LoRA (Low-Rank Adaptation, published by Microsoft researchers in 2021)275 is a shortcut: it leaves the original weights untouched and trains a small set of extra numbers that nudge the model's behaviour. Think of the model as an experienced professional, and a LoRA adapter as a short, specialised training course: it changes how they work in one area without replacing what they already know.

Base model (frozen) for example Qwen3.8-27B 27 billion weights 16 to 56 GB file never changed + LoRA adapter 10 MB to 1 GB = Specialised model loaded together or merged An adapter only fits the exact base model it was trained on: same family, same size, same version.
Figure 21.1. LoRA adapter: a small file that sits on top of one specific base model.

21.5.2 Facts that matter

21.5.3 What LoRA is good at, and bad at

Good atBad at
Style, format and tone (always answer in plain English, always produce a certain file layout)Adding large bodies of facts (a whole codebase, a medical textbook)
House conventions (how your team labels things, your patterns, your rules)Keeping facts up to date (it must be retrained)
A narrow, repeated task done the same way every timeMaking a weak base model strong
Shorter prompts (the instructions live in the adapter)Being trusted without testing

For facts, the better method is retrieval (often called RAG): the system finds the right documents and gives them to the model with the question. The model then answers from the text in front of it. Published guidance for practitioners in 2026 recommends starting with retrieval and adding a LoRA only when consistent behaviour is needed.278

21.5.4 What LoRA adapters are available today

This was searched specifically (Hugging Face and the web, November 2026):

What the search found for blackout topics (Hugging Face, 14 November 2026; search words: first aid, medical, survival, emergency, disaster, preparedness, off-grid, wilderness, and adapters for MedGemma, Qwen3.8 and Gemma 4):279

CandidateWhat it isWhy it is not recommended
EslamAhmed171/qwen-first-aid-assistantFirst aid adapter for Qwen2.5-1.5BVery small, old base model; no published tests or training data
QWERTYasdgf/Qwen-4B-FirstAid-LLMFirst aid model (merged, not an adapter), 4BNo published tests; unknown sources; cannot be checked against first aid guidelines
pixasocial/survival-uncensored-gemma-270m-v2Survival adapter for Gemma 3 270MSafety training removed ("uncensored"); tiny model that makes frequent errors
wattsonandme/survival-qwen-0.5bSurvival adapter for Qwen2.5-0.5BTiny model; no tests
rajveer43/gemma-4-E4B-medical-legal-finance-qaAdapter for Gemma 4 E4B (the 8 GB model in this chapter)General mixed questions and answers; no published tests or data sources
dawahealth/medgemma-maternal-lora-v2Maternal health adapter for MedGemma 4BNarrow subject; MedGemma alone already covers general medical questions
Adapters for Qwen3.8-27B (for example terse coding, HTML, writing style)Style and coding adaptersNone covers emergency topics; several remove safety training

Conclusion: no adapter for blackout topics has published tests, known training data and a current base model. Use MedGemma and the offline library instead, and train your own adapter only for your own material (section 21.6).

NeedBest toolLoRA?
Medical questionsMedGemma (4B now, 27B on the ideal tier) + WikiMed; always checked by a personNo (MedGemma is already specialised)
Water, sanitation, repair, foodAny good model + the zimgit, iFixit and DIY libraries + this guideNo
Plain-English notices and translationGemma 4 or Qwen3.8Optional small style adapter, not needed
Answering in the street's way (Charter, roles, procedures)This guide given as contextNo
Warning. Do not download and trust random adapters. An adapter can quietly degrade a model or change its behaviour, and there is no reliable way to inspect what it learned. Use only adapters you trained and tested yourself, or from a source you trust with published evaluations.

21.6 Training your own adapter

A community that maintains its own software can train an adapter on its code and documents. Do this while the internet and cloud computers are available. The limits in section 21.5.2 apply.

21.7 Serving AI to your street

  1. On the AI machine, start llama.cpp's server:
    llama-server -m "/path/to/models/gemma-4-E4B-it-Q4.gguf" \
      --host 127.0.0.1 --port 8081 -c 8192 --parallel 2
    Use 127.0.0.1 when the AI runs on the hub, so that only Caddy can reach it (on a Linux hub, where Docker cannot reach the host's 127.0.0.1, bind it to the Docker bridge address instead, for example 172.17.0.1), or the computer's network address when it runs on a second computer. On the ideal tier, use Qwen3.8-27B and a longer context.
  2. The hub's Caddy already routes https://ai.hub.example.org to port 8081 on the hub computer; point it at the AI machine's address if the AI runs on a second computer.
  3. Post the AI's hours on the notice board, set by the Power Lead.
  4. Set the safety instruction on the server, not in each person's browser: llama.cpp's built-in chat page stores instructions per browser, so use a front end that applies one instruction for everyone (for example Open WebUI)280 or start the model with a chat template that includes it. The instruction: answer in plain English, say when unsure, never identify plants or fungi as safe to eat, and for anything medical, electrical or safety-critical tell the user to check with the Health and Care Lead or the guide. Print the same rules at the AI desk.
  5. Retrieval from the library (letting the AI read library pages) needs a front end with document search; test one in the rehearsal before relying on it.
  6. Phones can also run small AI models themselves with an offline app installed in advance (for example PocketPal AI, which is open source and available for iPhone and Android)281. Install and test one now if wanted.

On an 8 GB machine, the AI cannot run well at the same time as the hub's other services. A second laptop is the practical answer for the street, even a modest one: Gemma 4 E4B needs only about 8 GB.

21.8 Checklist

Notes

  1. Qwen team, Alibaba, "Qwen3.8-27B" model card, Hugging Face, 2026. https://huggingface.co/Qwen/Qwen3.8-27B (accessed 14 November 2026). Back to text
  2. Google, "Gemma 4 E4B" model card (Apache-2.0; 4.5B effective parameters, 8B with embeddings), Hugging Face, 2026. https://huggingface.co/google/gemma-4-E4B-it (accessed 14 November 2026). Back to text
  3. Qwen team, Alibaba, "Qwen3.8-27B" model card, Hugging Face, 2026. https://huggingface.co/Qwen/Qwen3.8-27B (accessed 14 November 2026). Back to text
  4. Qwen team, Alibaba, "Qwen3.6-35B-A3B" model card, Hugging Face, 2026. https://huggingface.co/Qwen/Qwen3.6-35B-A3B (accessed 14 November 2026). Back to text
  5. Google Research, "Next generation medical image interpretation with MedGemma 1.5 and medical speech to text with MedASR", January 2026. https://research.google/blog/next-generation-medical-image-interpretation-with-medgemma-15-and-medical-speech-to-text-with-medasr/ (accessed 14 November 2026). Back to text
  6. Apple, "recommendedMaxWorkingSetSize" (Metal documentation: the memory limit the graphics processor should stay within). https://developer.apple.com/documentation/metal/mtldevice/recommendedmaxworkingsetsize (accessed 14 November 2026). Back to text
  7. Apple ml-explore, "mlx-lm" (running and fine-tuning language models with MLX, including LoRA). https://github.com/ml-explore/mlx-lm (accessed 14 November 2026). Back to text
  8. Kiwix, ZIM file downloads (sizes as listed, November 2026). https://download.kiwix.org/zim/ (accessed 14 November 2026). Back to text
  9. E. J. Hu and others, "LoRA: Low-Rank Adaptation of Large Language Models", arXiv:2106.09685, 2021. https://arxiv.org/abs/2106.09685 (accessed 14 November 2026). Back to text
  10. T. Dettmers and others, "QLoRA: Efficient Finetuning of Quantized LLMs", arXiv:2305.14314, 2023. https://arxiv.org/abs/2305.14314 (accessed 14 November 2026). Back to text
  11. ggml-org, "Introducing GGUF-my-LoRA" and llama.cpp LoRA adapter support. https://github.com/ggml-org/llama.cpp/discussions/10123 (accessed 14 November 2026). Back to text
  12. Machine Learning Mastery, "RAG vs Fine-Tuning for Domain Adaptation: When to Use Which". https://machinelearningmastery.com/rag-vs-fine-tuning-for-domain-adaptation-when-to-use-which/ (accessed 14 November 2026). Back to text
  13. Hugging Face, model search for LoRA adapters (searched 14 November 2026 for first aid, medical, survival, emergency, disaster, preparedness, off-grid, wilderness, MedGemma, Qwen3.8 and Gemma 4 adapters). https://huggingface.co/models?other=lora (accessed 14 November 2026). Back to text
  14. Open WebUI (self-hosted web front end for local AI models, with shared settings and document search). https://github.com/open-webui/open-webui (accessed 14 November 2026). Back to text
  15. PocketPal AI (open-source app that runs small language models offline on iPhone and Android). https://github.com/a-ghorbani/pocketpal-ai (accessed 14 November 2026). Back to text
Appendices

Cards, numbers and forms

Appendix APull-out cards

Each card starts on a new page, so you can print just these pages (choose the page range in the print settings) and pin them up, instead of cutting up the guide: by the sink, by the front door, at the water station and on the generator. The First Hour card is at the end of Part 1.

Water safety card

  1. First decide: tablets or bleach alone are enough only for water from a cold tap fed straight from the mains, drawn before the pressure dropped (in a loft-tank home, usually only the kitchen cold tap; in flats, ask, and if unsure treat it as open water). Mains water drawn before the pressure dropped and stored in clean, covered containers is safe as it is. All other water (river, canal, pond, roof rain, butt, loft tank, cylinder, bath, cistern, pipes, tap water after the pressure returns, sand or biosand filter output, output of any other filter): boil it, or filter it (0.1 micron, or a filter certified for cyst removal) and then chlorinate.
  2. Fuel or chemical smell, oily sheen, floodwater? Do not drink.
  3. Cloudy? Settle it for some hours, then strain through a folded cotton cloth.
  4. Boil: rolling boil for 1 minute. OR
  5. Tablets: as the packet says, wait 30 minutes (chlorine dioxide: see section 13.5). OR
  6. Plain unscented 5% bleach: 2 drops per litre (4 if cloudy or very cold). Other stated strength: drops per litre = 10 ÷ strength in %. Strength not given, or only "less than 5%": use tablets or boil. 1 level teaspoon per 50 litres. Stir, wait 30 minutes. Should smell faintly of chlorine. OR
  7. Sun (last resort; strong sun only, never in a cold-climate winter): clear plastic bottle, full sun 6 hours (2 days if cloudy).
  8. Store covered. Pour, do not dip. Wash hands with soap after the toilet and before food.
  9. Diarrhoea: 1 litre safe water + 6 level teaspoons sugar + half a level teaspoon salt. Sip often.

Pedal generator card

  1. Check: bike secure on stand, roller pressing on tyre, wires tight, fuse fitted, battery terminals covered.
  2. Check battery voltage before you start. Write it in the Battery Log.
  3. Pedal at a steady, comfortable pace in a gear that feels easy to keep up. If you have a DC watt meter, choose the gear that gives the most watts for the least effort.
  4. Stop at 14.4 V (gel batteries: 14.1 V).
  5. Lead-acid battery only, unless a charge controller is fitted rated for at least 50 V input (100 V with a treadmill motor), with its lithium setting chosen for a lithium battery.
  6. No diode fitted? Close the switch only while pedalling (never use the battery clamp as the switch). Disconnect before you stop.
  7. Shifts of 20 to 30 minutes. Write who pedalled and the voltage in the log.
  8. Charge outdoors or in a well-ventilated space, with no flames or sparks near the battery. Keep fingers, hair and clothes away from the wheel and roller.

Warmth and carbon monoxide card

  1. One room. Close doors. Block draughts. Blankets over windows.
  2. Layers, hat, socks. Sleep together. Hot water bottles (hot, not boiling).
  3. Warm food and drinks. Move every hour.
  4. Never indoors: generators, engines, barbecues, camping heaters or stoves, patio heaters. Never heat a room with a gas cooker.
  5. Headache, dizziness, sickness, several people ill at once? Get everyone outside into fresh air. Get help.
  6. Smell gas? No switches or flames. Open windows. Leave. Call the gas emergency number: ______________ (Great Britain: 0800 111 999).
  7. Home oxygen: keep it well away from any flame, fire or smoking.
  8. Check on older neighbours twice a day. The warm room is at: ______________________

Street network card

  1. Wi-Fi network: ______________________ Password: ______________________
  2. Hub address: ______________________ (or scan the QR code on the poster)
  3. Your phone may say "No internet". Stay connected. Android: tap "Keep connection"; turn off "Switch to mobile data".
  4. Save battery: aeroplane mode on, then turn only Wi-Fi back on.
  5. BitChat (if installed): open it and keep Bluetooth on to message nearby phones.
  6. Walkie-talkie channels: street ____ night watch ____ teams ____
  7. Help? Ask the Communications Lead at the meeting point.

When power returns

  1. Hot water cylinder drained? Refill it (open a hot tap until water runs) before you switch on the boiler or immersion heater. Only then remove the "Drained" notes.
  2. Generator in use? Switch the changeover switch back to mains before the generator is stopped.
  3. Do not switch everything on at once. Turn on lights first, then appliances one at a time over an hour, so the local electricity network is not overloaded and goes off again.
  4. Check for damage: any smell of burning or gas, water leaks from frozen pipes, appliances left on that could start a fire.
  5. Tap water: boil it until the water company says it is safe.
  6. Food: check the fridge and freezer (Chapter 19). When in doubt, throw it out.
  7. Medicines that needed a fridge: check with a pharmacist before use.
  8. Check on neighbours, especially people who live alone.
  9. Keep the street organised for a few days: outages can return. Hold a final community meeting to agree what to keep (contacts, the shared kit, the network) and restock the kits.

Appendix BKey numbers

Write your own country's numbers in the middle column now, while services work, and check each one. The right-hand column gives the United Kingdom's as an example.

ServiceYour number or frequencyExample: United Kingdom
Emergency (police, fire, ambulance, coastguard)______________999 or 112282 (112 also works across the European Union283)
Medical advice, not an emergency______________111 (NHS)284
Police, not an emergency______________101285
Power cuts______________105 (England, Scotland, Wales)286; 03457 643 643 (Northern Ireland)287
Gas emergency______________0800 111 999 (National Gas Emergency Service)288; 0800 002 001 (Northern Ireland)289
Priority list for vulnerable customers (energy and water)______________Priority Services Register, thepsr.co.uk290
Water supplier's emergency line______________Your water company
Local authority's emergency line______________Your council
Doctor's surgery or pharmacy______________Your GP surgery
National public radio (FM)______________BBC Radio 4, 92.4 to 94.6 FM291
Local radio (FM)______________Your BBC local station
Medium wave station (if still broadcasting)______________BBC Radio 5 Live, 693 or 909 kHz292
Other local stations (check on your own radio now)______________

In the UK, BBC Radio 4 long wave closed on 27 June 2026.293 Check every frequency on your own radio now, while services work, and write them on the radio itself.

Street details (fill in)
Meeting point
Meeting timesWhen the power has been off for one hour: the next full hour (08:00 if that falls at 21:00 or later, or earlier than 07:00); then 10:00 and 18:00 daily
Our street link(s) to neighbouring streets
Neighbourhood meeting place and time (street links)
Community meeting (day and time)
Water station
Warm room
Charging station / hub
Nearest defibrillators
Starlink households (with consent)

Notes

  1. UK Government, "999 and 112: the UK's national emergency numbers". https://www.gov.uk/guidance/999-and-112-the-uks-national-emergency-numbers (accessed 14 November 2026). Back to text
  2. European Commission, "112: the EU's emergency phone number" (free of charge from fixed and mobile phones everywhere in the EU). https://digital-strategy.ec.europa.eu/en/policies/112 (accessed 16 November 2026). Back to text
  3. NHS, "When to use 111". https://www.nhs.uk/nhs-services/urgent-and-emergency-care-services/when-to-use-111/ (accessed 14 November 2026). Back to text
  4. Police.uk, "Contact the police" (101 for non-emergencies). https://www.police.uk/pu/contact-us/ (accessed 14 November 2026). Back to text
  5. Energy Networks Association, "105 service" (free power cut number for England, Scotland and Wales). https://energynetworks.org/work/105-service (accessed 14 November 2026). Back to text
  6. NIE Networks, "Power cuts" (Northern Ireland: 03457 643 643). https://www.nienetworks.co.uk/power-cuts (accessed 14 November 2026). Back to text
  7. Energy Networks Association, "Smell gas?" (National Gas Emergency Service, 0800 111 999). https://www.energynetworks.org/customers/smell-gas (accessed 14 November 2026). Back to text
  8. NI Direct, "Energy, power supply and utilities" (Northern Ireland gas emergency: 0800 002 001). https://www.nidirect.gov.uk/articles/energy-power-supply-and-utilities (accessed 14 November 2026). Back to text
  9. Priority Services Register (energy and water companies), thepsr.co.uk. https://www.thepsr.co.uk/ (accessed 14 November 2026). Back to text
  10. BBC, "Radio reception" (frequencies by area). https://www.bbc.co.uk/reception/radio/ (accessed 14 November 2026). Back to text
  11. BBC, "Radio reception" (frequencies by area). https://www.bbc.co.uk/reception/radio/ (accessed 14 November 2026). Back to text
  12. TechRadar, "BBC waves bye-bye to its Long Wave broadcasts", June 2026. https://www.techradar.com/audio/a-classic-piece-of-tech-is-becoming-redundant-bbc-waves-bye-bye-to-its-long-wave-broadcasts (accessed 14 November 2026). Back to text

Appendix CPrintable forms

The forms are in a separate file so that each one prints on its own page (A4 or US Letter) and can be copied many times: printables/Street Forms.html.